Anyone have a good design for the rear mast (on rear cross brace) holder for trailering? Prindle 16. Boat goes in the water this week end.
Thanks, Harry
Design for Mast holder for trailering a P16
-
- Rank: Lubber
- Registered: May 21, 2009
- Last visit: May 23, 2011
- Posts: 12
Posted: Jun 30, 2009 - 09:30 PM
-
- Rank: Mate
- Registered: Feb 25, 2007
- Last visit: Jul 13, 2012
- Posts: 414
Posted: Jun 30, 2009 - 09:45 PM
I have a 6" piece of PVC. It's about 8" long. Cut a slot in one end for the mast to rest in. On the other end, shape it to set on the cross beam.
edited by: skarr1, Jul 01, 2009 - 05:20 PM -
- Rank: Lubber
- Registered: Apr 14, 2008
- Last visit: Apr 07, 2013
- Posts: 87
Posted: Jun 30, 2009 - 11:03 PM
got a pic< would love to see it -
- Rank: Mate
- Registered: Oct 19, 2006
- Last visit: Aug 16, 2017
- Posts: 613
Posted: Jun 30, 2009 - 11:53 PM
I made the same, cut a "V" slot in top, cut out a strip the entire length of the PVC, fits over traveler track, mast drops into "V"
--
TurboHobo
H14T
H16
P18
G-Cat 5.0
P16
-- -
- Rank: Master Chief
- Registered: Jun 20, 2006
- Last visit: Dec 04, 2024
- Posts: 7090
Posted: Jul 01, 2009 - 09:13 AM
on my H18 i used a milk crate and bungees
a life jacket makes a good rest as well. -
- Rank: Lubber
- Registered: Mar 25, 2009
- Last visit: Jun 15, 2010
- Posts: 54
Posted: Jul 01, 2009 - 09:24 AM
I used a vertical pole with a receiver style connection to the trailer. I also used a quick release pin to make connecting and disconnecting quicker.
I like this style because the mast is not resting on the boat. I live on a 1 mile long dirt road with lots of pot holes and with a mast cradle that rest on the boat it was hard to stop it from sliding side to side on the travel car rail due to the trapoline style not allowing me to secure the mast around the rear cross member.
Another reason i like this style is because the added insurance that the boat will not slide off the back of the trailer due to braking or acceleration because the vertical mast support acts as a stop for the boat. I usually tow the boat more than 50 miles to get to the water and this makes me feel alot more comfortable about doing so.
edited by: kinlawk, Jul 01, 2009 - 09:29 AM -
- Rank: Lubber
- Registered: May 08, 2009
- Last visit: Jun 11, 2010
- Posts: 46
Posted: Jul 01, 2009 - 10:04 AM
I use one of those foam noodles. Not the 3" diameter one, I found a 6" diameter one at Wal-Mart. I cut off a one foot section, and rest my mast on that. Plus, when it gets worn or lost, I still have three more feet to use. All for $2.99. -
- Rank: Mate
- Registered: Feb 25, 2007
- Last visit: Jul 13, 2012
- Posts: 414
Posted: Jul 01, 2009 - 05:21 PM
Instuctions
http://www.thebeachcats.c…pictures&g2_itemId=63131
And Andrew will tell you not to use bungee cords like the ones in the photos.
edited by: skarr1, Jul 01, 2009 - 04:25 PM -
- Rank: Lubber
- Registered: Jun 27, 2009
- Last visit: Jul 22, 2009
- Posts: 19
Posted: Jul 01, 2009 - 05:55 PM
Hey kinlawk can you email me at gcwilson777 at gmail dot com i need to ask you a couple questions thanks.
It needs a coat of paint but this is what mine came with
-
- Rank: Lubber
- Registered: Jan 22, 2009
- Last visit: Nov 23, 2014
- Posts: 99
Posted: Jul 02, 2009 - 07:25 AM
Skarr/steve, that's a nice looking mast cradle. It doesn't get more durable than PVC.
Thanks for posting the picture. -
- Rank: Lubber
- Registered: Jul 02, 2013
- Last visit: Apr 14, 2014
- Posts: 22
Posted: Aug 10, 2013 - 09:37 PM
Dang me!... After searching for something to buy and not finding anything I liked, I just went out to my garage and made a mast cradle for trailering that fits on the back crossbar of my Prindle 16... Looks a lot like the plywood one in the pics above. Total cost = 50 cents worth of electricity to run the sabre saw and drill. Everything else was scrap wood and spare drywall screws... Tomorrow I'll paint it using old spray paint... What fun!
--
Mike
1975 Prindle restoration project "Sanchah"
Retired Teacher
Newbie Sailor
-- -
- Rank: Lubber
- Registered: Jul 08, 2005
- Last visit: Aug 26, 2023
- Posts: 97
Posted: Aug 11, 2013 - 06:32 AM
if you want to get fancy, here's what is used with my h16. overkill probably but never any problems.
http://www.thebeachcats.com/pictures/?g2_itemId=88398
--
Mike Conway
H16
Hilton, NY
-- -
- Rank: Mate
- Registered: Aug 06, 2009
- Last visit: Jul 30, 2016
- Posts: 101
Posted: Aug 12, 2013 - 05:27 AM
i used a 4 in. 45degree pvc pipe joint. cut out a square piece on either side of the bottom to fit over traveler track. than set the mast on the top and pencil and cut out semicircles on the top to fit the angle of the mast. i use it on my solcat 18 and my nacra 18 square and it works great. tie it down to the crossbar and the mast when traveling. -
- Rank: Mate
- Registered: Aug 01, 2002
- Last visit: Nov 26, 2024
- Posts: 426
Posted: Aug 12, 2013 - 12:25 PM
That's using your noodle!
I did the same, but used two pieces.....one on the mast and one on the rear beam...which cross each other. Trim each a little to fit the contour somewhat....works great and is cheap and easy.
Edited by rattlenhum on Aug 12, 2013 - 12:26 PM.
--
Jerome Vaughan
Hobie 16
Clinton, Mississippi
-- -
- Rank: Lubber
- Registered: Dec 27, 2016
- Last visit: May 24, 2019
- Posts: 57
Posted: Jan 05, 2018 - 05:18 PM
Hey Jerome... Can u send me a pic of your mast cradle?... The noodle design. Thanks
--
Frank
Prindle 15/Hobie 16/Hobie 14T
-- -
- Rank: Mate
- Registered: Feb 05, 2011
- Last visit: Jun 15, 2021
- Posts: 575
Posted: Jan 06, 2018 - 06:04 PM
Same here.I use a 5'-0" stick of Uni-strut (available in the electrical aisle at HD) in a receiver made out of 2" box tubing. It has a bow roller on top with cradles. I put a foam bumper on the receiver to avoid damaging the hulls.
When I push the mast aft and pin it to the step the masthead is about 8 feet of the ground. That's a good starting height for raising.
http://www.unistrut.us/
--
'82 Super Cat 15
Hull #315
Virginia
Previously owned: '70 H14, '79 H16, '68 Sailmaster 26, '85 H14T
--
