I am going to a zipper luff jib and need to know the size and length of the jib halyard. It is not listed in the
manual. If anyone has a used one along with the s hook,
I would be interested in it.
Pete
edited by: pknapp66, Jun 24, 2010 - 04:49 PM
--
Pete Knapp
Schodack landing,NY
Goodall Viper,AHPC Viper,Nacra I20
--
P16 jib halyard
-
- Rank: Mate
- Registered: May 09, 2009
- Last visit: Aug 14, 2024
- Posts: 686
Posted: Jun 24, 2010 - 04:48 PM
-
- Rank: Lubber
- Registered: Apr 05, 2010
- Last visit: Jul 31, 2010
- Posts: 36
Posted: Jun 24, 2010 - 05:07 PM
According to Salty Dog Marine: Jib Halyard - 5/32? (4mm) x 22' (670.6cm) Hope that helps!
Steve -
- Rank: Mate
- Registered: Jul 06, 2008
- Last visit: Jul 19, 2018
- Posts: 986
Posted: Jun 24, 2010 - 05:12 PM
Courtesy of Salty Dog marine
Barberhauler - 1/4? (6.4mm) x 16? (487.7cm)
Batten Ties - 3/32? (2mm) x 22? (55.9cm) (8)
Downhaul - 1/4? (6.4mm) x 15? (457.2cm)
Jib Clew Bridle - 3/16? (5mm) x 6? (182.9cm)
Jib Halyard - 5/32? (4mm) x 22' (670.6cm) (2)
Jib Sheet - 5/16? (8mm) x 33? (1005.8cm)
Main Halyard - 3/16? (5mm) x 52' (1585cm)
Main Sheet - 3/8? (9mm) x 40' (1219.2cm)
Rudder Pull Down - 1/4? (6.4mm) x 4? (121.9cm) (2)
Rudder Pull Up - 1/4? (6.4mm) x 5? (152.4cm) (2)
Tramp Lace Rear - 3/16? (5mm) x 10' 6" (320.0cm) (2)
Tramp Lace Side - 5/32" (4mm) x 11' (335.3cm) (2)
Trapeze Adjustment - 1/4? (6.4mm) x 3' 6" (106.7cm) (4)
Traveler - 5/16? (8mm) x 10? (304.8cm)
--
Dustin Finlinson • Magna, UT
Member: Utah Sailing Association
1982 Prindle 18
1986 Hobie 17
1982 Prindle 16
1980 Prindle 16(mostly)
1976 Prindle 16(mostly)
Check out "Prindle Sailors" on Facebook.
-- -
- Rank: Mate
- Registered: May 09, 2009
- Last visit: Aug 14, 2024
- Posts: 686
Posted: Jun 24, 2010 - 05:43 PM
From Salty Dog's catalog:
PRINDLE JIB HALYARD LINE WITH SISTER CLIPS $20.00
PRINDLE 16 MAIN HALYARD 3/32" (2.4mm) $46.00
PRINDLE 16 JIB HALYARD 1/8" (3.2mm) $41.40
My manual shows the halyard with sister clips. More confused than before.
--
Pete Knapp
Schodack landing,NY
Goodall Viper,AHPC Viper,Nacra I20
-- -
- Rank: Mate
- Registered: Mar 12, 2003
- Last visit: Feb 19, 2021
- Posts: 879
Posted: Jun 24, 2010 - 05:55 PM
If you had the old wire luff jib before, you will have to order a new upper forestay with ring and either cut down current forestay or order new forestay. Then you will need about 34' of 1/8 or 3/16 line with sister clips, S hook and halyard shackle. Pete -
- Rank: Mate
- Registered: May 09, 2009
- Last visit: Aug 14, 2024
- Posts: 686
Posted: Jun 24, 2010 - 06:04 PM
Hey Pete I knew you would give me the answer. I have all of the proper rigging for the zipper luff jib except the halyard and s hook.
edited by: pknapp66, Jun 24, 2010 - 06:45 PM
--
Pete Knapp
Schodack landing,NY
Goodall Viper,AHPC Viper,Nacra I20
--
Users on-line
This list is based on users active over the last 60 minutes.