. I know hobie sells mast steppers but is there any other options? 2) Is there a way to transport the boat with the rudders attached? With the way the mast sits on the rear cross member for the trampoline during transport you have to remove the rudders. Is there another option? 3) what is the easiest wat to get the boat back on the trailer without a launch? I am picking up a set of cat trax tomorrow. Will these help? Thanks in advance for your help.
Trailering Getaway with rudders attached
-
- Rank: Mate
- Registered: Jul 18, 2010
- Last visit: Jul 28, 2013
- Posts: 143
Posted: Jul 23, 2010 - 10:49 PM
Well me and a fellow forum member Golfdad75 took my new used getaway out today and I have to say it was a blast. Without his help I would have been lost trying to set up the first time. It really is nice to have forum members that do not mind taking time out of there day to help a newbie. Thanks Terry. There are only three things I need advice on. 1) Something to help stepping the mast. I have a bad back and I can see myself hurting it again . I know hobie sells mast steppers but is there any other options? 2) Is there a way to transport the boat with the rudders attached? With the way the mast sits on the rear cross member for the trampoline during transport you have to remove the rudders. Is there another option? 3) what is the easiest wat to get the boat back on the trailer without a launch? I am picking up a set of cat trax tomorrow. Will these help? Thanks in advance for your help.
-
- Rank: Mate
- Registered: Feb 25, 2007
- Last visit: Jul 13, 2012
- Posts: 414
Posted: Jul 23, 2010 - 11:31 PM
This works on my nacra. Just a piece of PVC pipe. -
- Rank: Mate
- Registered: Jul 18, 2010
- Last visit: Jul 28, 2013
- Posts: 143
Posted: Jul 23, 2010 - 11:46 PM
That would probably work. I will look into that tomorrow if the weather is nice. Thanks -
- Rank: Mate
- Registered: Feb 25, 2007
- Last visit: Jul 13, 2012
- Posts: 414
Posted: Jul 23, 2010 - 11:54 PM
I have transported my boat for years with the rudders on, but it is not recommended. -
- Rank: Mate
- Registered: Jul 18, 2010
- Last visit: Jul 28, 2013
- Posts: 143
Posted: Jul 24, 2010 - 10:31 AM
Why is that not recommended? -
- Rank: Chief
- Registered: Jul 16, 2009
- Last visit: Oct 28, 2014
- Posts: 1271
Posted: Jul 24, 2010 - 10:32 AM
since you are mainly trailoring local to launch site, i would keep rudders on but if its a long haul take them off. here is a pic of my mast bracket, its fast and easy to use.go to members albums and click on "prindle 16 hull repair and paint" find this pic and click on it a second time for a closer look(larger image). note 1/2" line tied around rudders and castings to keep rudders up during trailoring.
--
Check out "Prindle Sailors" on Facebook!
bill harris
hattiesburg, mississippi
prindle 16- "BLUE RIBBON"
-- -
- Rank: Mate
- Registered: Jul 18, 2010
- Last visit: Jul 28, 2013
- Posts: 143
Posted: Jul 24, 2010 - 10:37 AM
I looked at the larger picture but cant tell what it is? Did you make it or buy it? Thanks -
- Rank: Mate
- Registered: Feb 25, 2007
- Last visit: Jul 13, 2012
- Posts: 414
Posted: Jul 24, 2010 - 10:41 AM
The bouncing around will wear out all the moving attachment points.
I leave my rudders on, tie them down so they don't swing.
I also use bungee cords on each tiller arm pulling down on the forward end. This will keep the rudders from bouncing around. -
- Rank: Chief
- Registered: Jul 16, 2009
- Last visit: Oct 28, 2014
- Posts: 1271
Posted: Jul 24, 2010 - 01:02 PM
store bought, previous owner...can't help you there, but sure there out there...makes trailoring that much faster.
--
Check out "Prindle Sailors" on Facebook!
bill harris
hattiesburg, mississippi
prindle 16- "BLUE RIBBON"
-- -
- Rank: Mate
- Registered: Jul 18, 2010
- Last visit: Jul 28, 2013
- Posts: 143
Posted: Jul 25, 2010 - 01:44 PM
I think I am going to try and use a piece of PVC pipe. Now the hard part is finding a short piece of pipe.I cant see buying a 8ft stick for 10 inches. -
- Rank: Mate
- Registered: Jan 14, 2004
- Last visit: Sep 25, 2024
- Posts: 866
Posted: Jul 25, 2010 - 01:56 PM
all you need is a pvc coupling, 4" or 6". I've used a 4" coupling for years trouble free.
--
Philip
-- -
- Rank: Mate
- Registered: Feb 25, 2007
- Last visit: Jul 13, 2012
- Posts: 414
Posted: Jul 25, 2010 - 02:10 PM
edited by: skarr1, Jul 25, 2010 - 01:11 PM -
- Rank: Mate
- Registered: Jul 18, 2010
- Last visit: Jul 28, 2013
- Posts: 143
Posted: Jul 25, 2010 - 02:17 PM
I will try that. Thanks -
- Rank: Mate
- Registered: Feb 25, 2007
- Last visit: Jul 13, 2012
- Posts: 414
Posted: Jul 25, 2010 - 04:38 PM
I have 5 feet of 4 inch pvc. I might be in Panama City at Carl Gray Park next weekend. -
- Rank: Mate
- Registered: Jul 18, 2010
- Last visit: Jul 28, 2013
- Posts: 143
Posted: Jul 25, 2010 - 05:33 PM
I appreciate it but I ended up finding a piece at my fathers house. Carl Gray park, what is this? Is it a place to sail? I am familiar with St. Andrews but not Carl Gray. -
- Rank: Mate
- Registered: Feb 25, 2007
- Last visit: Jul 13, 2012
- Posts: 414
Posted: Jul 25, 2010 - 08:21 PM
-
- Rank: Mate
- Registered: Jul 18, 2010
- Last visit: Jul 28, 2013
- Posts: 143
Posted: Jul 25, 2010 - 08:57 PM
Ah I see. Thanks
Users on-line
- 0 users
This list is based on users active over the last 60 minutes.