• motivated
  
  

  • Rank: Mate
  • Registered: May 27, 2011
  • Last visit: Sep 17, 2014
  • Posts: 145

  Posted: Aug 27, 2011 - 10:00 PM

  I installed some hull cradles (by Sailboxes.com, an advertiser here) on the trailer today. It took about 3 hours, but boy o' boy, do they work well. Such a drastic improvement over the cheap rollers that came with the trailer. These things are awesome. Pics are below:
  
  Front Cradle
  
  
  Rear Cradle
  
  
  --
  Karl, Captain of Stayin' Thirsty
  2011 Hobie 16SE
  Atlanta, GA
  --

  • 
  •  
• Wolfman
  
  

  • Rank: Chief
  • Registered: Jun 24, 2009
  • Last visit: Jun 15, 2023
  • Posts: 1555

  Posted: Aug 27, 2011 - 10:03 PM

  Awesome, I may have to look those up!
  
  --
  Dave Bonin
  1981 Nacra 5.2 "Lucile"
  1986 Nacra 5.7 "Belle"
  Winnipeg, Manitoba, Canada
  --

  • 
  •  
• KennyB
  
  

  • Rank: Mate
  • Registered: Nov 16, 2002
  • Last visit: Jul 04, 2020
  • Posts: 139

  Posted: Aug 28, 2011 - 08:41 AM

  Thanks for the compliment Karl...good job on the installation.
  
  --
  Kenny Boudreaux
  2010 C2 F18 USA 323
  Goodall Design "Southern Area Rep"
  Owner of Sailboxes.com
  --

  • 
  •  
• klozhald
  
  

  • Rank: Chief
  • Registered: Apr 19, 2011
  • Last visit: Nov 20, 2024
  • Posts: 1460

  Posted: Dec 05, 2011 - 02:37 PM

  motivated

  It took about 3 hours, but boy o' boy, do they work well.

  
  
  Did you use the roller brackets that came with your trailer to mount the cradles?
  Did the steel plates that you show on the side of the cradle (that the pivot pin runs through) come with the cradles?
  
  --
  Sheet In!
  Bob
  _/)_____/)_/)____/)____/)_____/)/)__________/)__
  Prindle 18-2 #244 "Wakizashi"
  Prindle 16 #3690 "Pegasus" Sold (sigh)
  AZ Multihull Fleet 42 member
  (Way) Past Commodore of Prindle Fleet 14
  Arizona, USA
  --

  • 
  •  
• Edchris177
  
  

  • Rank: Chief
  • Registered: Nov 26, 2009
  • Last visit: Aug 10, 2024
  • Posts: 2531

  Posted: Dec 05, 2011 - 06:57 PM

  Quote

  Awesome, I may have to look those up!

  
  Forget it Dave, you don't care if your hulls break. I have two extras in my back yard waiting for you. One was rebuilt with carbon fibre & kevlar from the Osprey V-22 program, my buddy went down & bought nearly all available after they canceled that project, some will find its way into the N36 this summer.
  I also have your extra boards, & your choice of boom.
  
  --
  Hobie 18 Magnum
  Dart 15
  Mystere 6.0XL Sold Was a handful solo
  Nacra 5.7
  Nacra 5.0
  Bombardier Invitation (Now officially DEAD)
  Various other Dock cluttering WaterCrap
  --

  • 
  •  
• motivated
  
  

  • Rank: Mate
  • Registered: May 27, 2011
  • Last visit: Sep 17, 2014
  • Posts: 145

  Posted: Dec 06, 2011 - 04:51 AM

  klozhald

  motivated

  It took about 3 hours, but boy o' boy, do they work well.

  
  
  Did you use the roller brackets that came with your trailer to mount the cradles?
  Did the steel plates that you show on the side of the cradle (that the pivot pin runs through) come with the cradles?

  
  
  Yes, I removed the rubber rollers from the roller brackets on the rear and used half of the roller for the front. The front cradles don't need much in the way of lateral movement. The rear cradles need more lateral leeway, so I removed the entire roller.
  
  The steel plates are simple zinc plated cut washers from Home Depot (I believe they are 5/8's). I used a drill press to drill out the three holes in the washers and used stainless bolts with locknuts for fastners. You can gain access to the interior of the cradle by simply cutting away the carpet on the top (so you can put the nuts on the end of the bolts).
  
  I've had them on the trailer now for a few months and so far, they're working perfectly. I feel much more confident when going on those long road trips with the Hobie in tow.
  
  
  
  Edited by motivated on Dec 06, 2011 - 05:51 AM.
  
  --
  Karl, Captain of Stayin' Thirsty
  2011 Hobie 16SE
  Atlanta, GA
  --

  • 
  •  
• Headhunter
  
  

  • Rank: Mate
  • Registered: Jan 18, 2006
  • Last visit: Aug 07, 2020
  • Posts: 156

  Posted: Dec 06, 2011 - 06:59 AM

  Cradles are nice, I have a pair. My observation from long term use is they trap moisture causing blisters. Anyone else have this happen?

  • 
  •  
• klozhald
  
  

  • Rank: Chief
  • Registered: Apr 19, 2011
  • Last visit: Nov 20, 2024
  • Posts: 1460

  Posted: Dec 06, 2011 - 05:08 PM

  headhunter

  Cradles are nice, I have a pair. My observation from long term use is they trap moisture causing blisters. Anyone else have this happen?

  
  
  There are mentions of blistering in other threads.
  If you search the forums, you'll find them.
  Sheet In!
  
  --
  Sheet In!
  Bob
  _/)_____/)_/)____/)____/)_____/)/)__________/)__
  Prindle 18-2 #244 "Wakizashi"
  Prindle 16 #3690 "Pegasus" Sold (sigh)
  AZ Multihull Fleet 42 member
  (Way) Past Commodore of Prindle Fleet 14
  Arizona, USA
  --

  • 
  •  
•  
•  

Users on-line

• 0 users

This list is based on users active over the last 60 minutes.