My old Tornado cat has strong weather helm on a starboard tack and strong lee helm on a port tack. Obvisouly some asymmmerty somewhere. Any suggestions on where to look? Using sail trim I have to stall the main on one tack and luff it on the other just to make the helm managable.
Thnaks, Michael
Asymmetrical helm
-
- Rank: Lubber
- Registered: Dec 08, 2011
- Last visit: Dec 12, 2011
- Posts: 2
Posted: Dec 08, 2011 - 01:28 PM
-
- Rank: Master Chief
- Registered: Jun 20, 2006
- Last visit: May 22, 2024
- Posts: 7089
Posted: Dec 08, 2011 - 03:03 PM
are your rudders on backwards? kidding
perhaps your mast is not over the CE
perhaps your boards are not tucked under the same
perhaps a board or rudder is warped -
- Rank: Mate
- Registered: Jul 06, 2008
- Last visit: Jul 19, 2018
- Posts: 986
Posted: Dec 08, 2011 - 09:41 PM
I have had something similar when one rudder wasn't quite locking down right,
--
Dustin Finlinson • Magna, UT
Member: Utah Sailing Association
1982 Prindle 18
1986 Hobie 17
1982 Prindle 16
1980 Prindle 16(mostly)
1976 Prindle 16(mostly)
Check out "Prindle Sailors" on Facebook.
-- -
- Rank: Chief
- Registered: Nov 26, 2009
- Last visit: Aug 10, 2024
- Posts: 2531
Posted: Dec 11, 2011 - 06:59 PM
I sailed my 5.7 that way for a year. I put levels on the mast,thinking one shroud was shorter, checked rudders, diagonals etc. I looked for a bent mast, & made sure rudders were the same geometry. I measured the ends of the hulls & found they were not in alignment. I finally pinned it to a front beam that had a slight kink, right near the connection to the starboard hull. This forced one hull into a lean, & pointing off center. I replaced the front beam.
--
Hobie 18 Magnum
Dart 15
Mystere 6.0XL Sold Was a handful solo
Nacra 5.7
Nacra 5.0
Bombardier Invitation (Now officially DEAD)
Various other Dock cluttering WaterCrap
-- -
- Rank: Master Chief
- Registered: Jun 20, 2006
- Last visit: May 22, 2024
- Posts: 7089
Posted: Dec 12, 2011 - 07:36 AM
+1 Edchris177
i was just thinking this weekend, that your beams are not square -
- Rank: Lubber
- Registered: Dec 08, 2011
- Last visit: Dec 12, 2011
- Posts: 2
Posted: Dec 12, 2011 - 03:09 PM
Some good ideas. I'm off to take some measurements.
Thnaks for you help,
Michael -
- Rank: Chief
- Registered: Apr 19, 2011
- Last visit: Nov 20, 2024
- Posts: 1460
Posted: Dec 13, 2011 - 08:48 AM
Nice find.
It wouldn't take much of a kink to give this effect.
sandrimr check the crossbar beds in the hulls for integrity.
A sloppy mount (fiberglass or hardware) would give the same effeect.
Edited by klozhald on Dec 13, 2011 - 08:50 AM.
--
Sheet In!
Bob
_/)_____/)_/)____/)____/)_____/)/)__________/)__
Prindle 18-2 #244 "Wakizashi"
Prindle 16 #3690 "Pegasus" Sold (sigh)
AZ Multihull Fleet 42 member
(Way) Past Commodore of Prindle Fleet 14
Arizona, USA
--
Users on-line
- 0 users
This list is based on users active over the last 60 minutes.