Edited by klppurdy on May 19, 2012 - 05:57 PM.
--
Kenneth Purdy
Hobie 16
Nacra 5.2 (2)
Banshee
First Coast, Florida
--
Fiberglass Repair - Daggerboard
-
- Rank: Mate
- Registered: Aug 16, 2011
- Last visit: Jun 03, 2022
- Posts: 224
Posted: May 19, 2012 - 05:52 PM
Ok, these shots are off my banshee dingee, not a catamaran, but i thought i would see what you guys think repair wise, there is a little chunk where the daggerboard slot is, what do you think
Edited by klppurdy on May 19, 2012 - 05:57 PM.
--
Kenneth Purdy
Hobie 16
Nacra 5.2 (2)
Banshee
First Coast, Florida
-- -
- Rank: Lubber
- Registered: Jan 09, 2012
- Last visit: May 17, 2013
- Posts: 78
Posted: May 20, 2012 - 06:49 AM
Marine bondo type filler and a few coats of gel coat. -
- Rank: Mate
- Registered: May 09, 2009
- Last visit: Aug 14, 2024
- Posts: 686
Posted: May 20, 2012 - 07:37 AM
I would just fill that in with marine tex and sand it out. will be tough and look pretty decent.
Friend has a Banshee. Blast to sail for a dinghy.
--
Pete Knapp
Schodack landing,NY
Goodall Viper,AHPC Viper,Nacra I20
-- -
- Rank: Mate
- Registered: Aug 16, 2011
- Last visit: Jun 03, 2022
- Posts: 224
Posted: May 20, 2012 - 08:18 AM
i have not had the opportunity to sail it yet, but.......it looks fun.
--
Kenneth Purdy
Hobie 16
Nacra 5.2 (2)
Banshee
First Coast, Florida
-- -
- Rank: Chief
- Registered: Nov 26, 2009
- Last visit: Aug 10, 2024
- Posts: 2531
Posted: May 20, 2012 - 08:38 AM
Dagger board slots need to be strong. It looks like there is minimal damage, top photo I would use a dremel like tool & remove the cracked gelcote, & damaged glass.
Use a Popsicle stick to cram the ground out slot with glass matting, then pour a bit of resin in & work it into the matt with the stick. Let it set up & sand to fair it out.
Bottom of hull looks purely cosmetic, 1 layer of matt with just enough resin to wet it, or a bit of marine tex. Smooth it with a gloved finger prior to kicking off, then sand an hour later.
The entire job will be done in an hour, unless you decide to apply gelcote too.
--
Hobie 18 Magnum
Dart 15
Mystere 6.0XL Sold Was a handful solo
Nacra 5.7
Nacra 5.0
Bombardier Invitation (Now officially DEAD)
Various other Dock cluttering WaterCrap
-- -
- Rank: Mate
- Registered: Jul 16, 2002
- Last visit: Aug 18, 2020
- Posts: 126
Posted: May 20, 2012 - 07:01 PM
It looks like there have been some attempts to patch this before with some crappy methods. I would cut all the BS out plus any glass that is white. A 4 1/2 in Angle Grinder with a 60grit disc will do it fast and a fan blowing it away from you will keep you from getting all itchy. All the glass material should be an amber color to show it was well saturated. Get some Polyester Resin w/hardner, 3- 4oz mat and some 1in chip brushes. Cut strips wider than the area you cut out then pull the glass apart so it does not have a crisp edge. Mix the resin a bit hot - a good squirt vs a few drops. Dont tarry in putting this on the boat wet out the strips until the repair is proud (sticks up) Once it kicks in a hour or so you can grind it fair and finish w gel-coat.
I use waxed paper dixie cups for the resin - pour up three or four half full and add the hardner but dont stir until ready to use
--
Lee - On the BIG Lake in MS
Harstil Kaulua 31 - Current Project Boat
Cal 25 - What ? Time to freshen it up again??
MC Scow 16 (1 in the water and 1 parts/project) SOLD
Capri 22 - What do you mean you wont deliver it??
Chrysler Pirateer 13 - new addition to the fleet
--
Users on-line
- 0 users
This list is based on users active over the last 60 minutes.