Beach wheel help :: Catamaran Sailboats at TheBeachcats.com

Beach wheel help

optikid

Rank: Mate

Registered: May 29, 2011

Last visit: Mar 13, 2016

Posts: 332
Posted: Jul 16, 2012 - 09:51 PM

Hi, i was looking at my beach wheels and the bearings dont look right.

any ideas?
Quarath

Rank: Mate

Registered: Jul 06, 2008

Last visit: Jul 19, 2018

Posts: 986
Posted: Jul 17, 2012 - 01:22 PM

Get rid of the PVC, that was for the old style you don't need it anymore. You should have 20 delrin rollers inside each hub. All you need is a the flat stainless or nylon washer (mine has both) that sits right against the rim on each side to hold the rollers in place. Give the rollers a spraying with sailkote before you seal em up. If you are converting from old style to new you may need to drill a new hole on one side for the cotter pin to go through as the old holes were wider apart.

--
Dustin Finlinson • Magna, UT
Member: Utah Sailing Association
1982 Prindle 18
1986 Hobie 17
1982 Prindle 16
1980 Prindle 16(mostly)
1976 Prindle 16(mostly)
Check out "Prindle Sailors" on Facebook.
--
optikid

Rank: Mate

Registered: May 29, 2011

Last visit: Mar 13, 2016

Posts: 332
Posted: Jul 17, 2012 - 06:10 PM

i bought them like that... and i have a metal washer.
optikid

Rank: Mate

Registered: May 29, 2011

Last visit: Mar 13, 2016

Posts: 332
Posted: Jul 19, 2012 - 05:49 AM

do i need the nylon one?
MN3

Rank: Master Chief

Registered: Jun 20, 2006

Last visit: May 22, 2024

Posts: 7089
Posted: Jul 19, 2012 - 06:50 AM

QuoteGive the rollers a spraying with sailkote before you seal em up.

sailkote is not recommended for bearings.. it will cause sand to stick to em' and leave flat spots

fresh water rinse is suggested

FWIW
Quarath

Rank: Mate

Registered: Jul 06, 2008

Last visit: Jul 19, 2018

Posts: 986
Posted: Jul 19, 2012 - 01:35 PM

I happened to have both the old metal and the new nylon ones when I converted mine so I put the metal against the wheel and the nylon next to it and then cotter pinned it. You probably do not need both.

--
Dustin Finlinson • Magna, UT
Member: Utah Sailing Association
1982 Prindle 18
1986 Hobie 17
1982 Prindle 16
1980 Prindle 16(mostly)
1976 Prindle 16(mostly)
Check out "Prindle Sailors" on Facebook.
--
Quarath

Rank: Mate

Registered: Jul 06, 2008

Last visit: Jul 19, 2018

Posts: 986
Posted: Jul 19, 2012 - 01:37 PM

MN3
QuoteGive the rollers a spraying with sailkote before you seal em up.

sailkote is not recommended for bearings.. it will cause sand to stick to em' and leave flat spots

fresh water rinse is suggested

FWIW

Didn't know that I kind of treat it like WD40 for the boat. A little here and there helps everything. But mostly I apply it to the edge of bolt rope that hits the track most every season.

Edited by Quarath on Jul 19, 2012 - 01:39 PM.

--
Dustin Finlinson • Magna, UT
Member: Utah Sailing Association
1982 Prindle 18
1986 Hobie 17
1982 Prindle 16
1980 Prindle 16(mostly)
1976 Prindle 16(mostly)
Check out "Prindle Sailors" on Facebook.
--
MN3

Rank: Master Chief

Registered: Jun 20, 2006

Last visit: May 22, 2024

Posts: 7089
Posted: Jul 20, 2012 - 07:06 AM

a swollen boltrope / dented track is a good use for sailkote , so is sparying on a spin so it will snuff better...
PurdueZach

Rank: Mate

Registered: Apr 24, 2011

Last visit: Mar 20, 2018

Posts: 177
Posted: Jul 20, 2012 - 09:10 AM

MN3a swollen boltrope / dented track is a good use for sailkote , so is sparying on a spin so it will snuff better...

I even used it in a pinch last night to loosen up a stuck lock on my cat box.

--
-Zach
--