I've read several posts stating that people's trailers have Cat Trax holders, and I've searched for a picture of what they look like with no luck... Can someone post a picture of how they have them mounted to the trailer when traveling? Currently, I just tie mine to the tramp and pray they don't fall off.
Thanks-
Chris
--
16' Prindle
Emerald Coast of Florida
--
Cat Trax -- Trailer Holders
-
- Rank: Lubber
- Registered: Jun 03, 2012
- Last visit: Jun 08, 2014
- Posts: 55
Posted: May 06, 2013 - 05:43 PM
-
- Rank: Mate
- Registered: Apr 24, 2011
- Last visit: Mar 20, 2018
- Posts: 177
Posted: May 06, 2013 - 06:25 PM
I would be curious to hear other's responses. I put mine on the top of the hulls on the front or rear. Some people put theirs on the trailer crossbars underneath.
--
-Zach
-- -
- Rank: Mate
- Registered: Jan 14, 2004
- Last visit: Sep 25, 2024
- Posts: 866
Posted: May 06, 2013 - 07:29 PM
This is the best system I have had on any and all my boats. Catrax axle held in place with a trucker's rubber hood latch. Enlarge picture and zoom to bottom. You can see one of the two vertical support post that are part of the trailer's a-frame. Image is in my folder.
--
Philip
-- -
- Rank: Mate
- Registered: Jul 06, 2008
- Last visit: Jul 19, 2018
- Posts: 986
Posted: May 07, 2013 - 01:02 PM
Mine just ride across the top of the hulls as well.
--
Dustin Finlinson • Magna, UT
Member: Utah Sailing Association
1982 Prindle 18
1986 Hobie 17
1982 Prindle 16
1980 Prindle 16(mostly)
1976 Prindle 16(mostly)
Check out "Prindle Sailors" on Facebook.
-- -
- Rank: Mate
- Registered: Jan 21, 2003
- Last visit: Feb 10, 2015
- Posts: 115
Posted: May 07, 2013 - 03:07 PM
I put my setup in the tech photos section. Can take more and better photos upon request
--
Jeff
Houston TX
1986 Hobie 18 Sail# 13031
-- -
- Rank: Chief
- Registered: Jul 16, 2009
- Last visit: Oct 28, 2014
- Posts: 1271
Posted: May 07, 2013 - 08:55 PM
i have a sheet of marine plywood on the trailor. i put a cleat on both ends and cleat the cattrax to it...easy!
--
Check out "Prindle Sailors" on Facebook!
bill harris
hattiesburg, mississippi
prindle 16- "BLUE RIBBON"
-- -
- Rank: Mate
- Registered: Jan 14, 2004
- Last visit: Sep 25, 2024
- Posts: 866
Posted: May 07, 2013 - 10:23 PM
That PBR keg better be empty . . .
--
Philip
-- -
- Rank: Lubber
- Registered: Jul 15, 2011
- Last visit: Jul 08, 2014
- Posts: 2
Posted: May 08, 2013 - 07:24 AM
My trailex has 2 vertical posts (about 2 ft tall) on the toung between the front mast support and where the boat box is mounted. Each post has a rubber V-shaped cradle. The distance between the posts locates them just on the outside of the cat trax wheels.
I've had this set-up on 2 trailers and works very well. -
- Rank: Mate
- Registered: Aug 01, 2002
- Last visit: Sep 14, 2024
- Posts: 425
Posted: May 08, 2013 - 12:04 PM
Bloody brilliant! I'm not sure that I have enough room between the sail box and mast crutch....gonna check on that.
--
Jerome Vaughan
Hobie 16
Clinton, Mississippi
-- -
- Rank: Chief
- Registered: Jul 16, 2009
- Last visit: Oct 28, 2014
- Posts: 1271
Posted: May 08, 2013 - 12:07 PM
it was drained in less than 6 hours after hooking it up, it amazing how many friends you have when tap a keg! looking into homebrewing, i have several old kegs around and am looking to put them to use...bulk buying and all that.
--
Check out "Prindle Sailors" on Facebook!
bill harris
hattiesburg, mississippi
prindle 16- "BLUE RIBBON"
--
Users on-line
- 0 users
This list is based on users active over the last 60 minutes.