Just bought a pair of blocks for the downhaul.
I cant quite figure out how to reeve these with the becket located where it is.
Thanks in advance.
Need Help Reeving
-
- Rank: Lubber
- Registered: Mar 31, 2013
- Last visit: May 31, 2013
- Posts: 8
Posted: May 29, 2013 - 01:16 PM
Hi all,
Just bought a pair of blocks for the downhaul.
I cant quite figure out how to reeve these with the becket located where it is.
Thanks in advance.
-
- Rank: Master Chief
- Registered: Jun 20, 2006
- Last visit: May 22, 2024
- Posts: 7089
Posted: May 29, 2013 - 01:22 PM
I would try this pattern but start on top at the becket
Edited by MN3 on May 29, 2013 - 01:24 PM. -
- Rank: Lubber
- Registered: Mar 31, 2013
- Last visit: May 31, 2013
- Posts: 8
Posted: May 29, 2013 - 01:30 PM
I gave those a try with no luck. Im thinking I may have to add an eyelet on top of the cam cleat and using that as a becket. not sure though... -
- Rank: Mate
- Registered: Nov 02, 2004
- Last visit: Aug 07, 2023
- Posts: 626
Posted: May 29, 2013 - 01:42 PM
Becket needs to be on the bottom. What boat are you putting it on?
--
Ron
Nacra F18
Reservoir Sailing Assn.
Brandon, Mississippi
-- -
- Rank: Lubber
- Registered: Mar 31, 2013
- Last visit: May 31, 2013
- Posts: 8
Posted: May 29, 2013 - 01:46 PM
ya. after more experimenting I realized I need the becket on the bottom... do you think an added eyelet will suffice as a becket? Its for an H16 downhaul -
- Rank: Mate
- Registered: Nov 02, 2004
- Last visit: Aug 07, 2023
- Posts: 626
Posted: May 29, 2013 - 01:56 PM
If you mean putting an eyestrap above the camcleat, you may not have room for the tie off and the uncleated line in the space of the eyestrap but it's worth a try.
--
Ron
Nacra F18
Reservoir Sailing Assn.
Brandon, Mississippi
-- -
- Rank: Mate
- Registered: Mar 12, 2003
- Last visit: Feb 19, 2021
- Posts: 879
Posted: May 29, 2013 - 02:19 PM
I don't see how you need either becket. Start at cam cleat, go up to triple (to the side), down to cam cleat triple, then up & down twice and DEADEND on last sheave of cam cleat triple (with simple knot not allowing go thru sheave.). Pete -
- Rank: Lubber
- Registered: Mar 31, 2013
- Last visit: May 31, 2013
- Posts: 8
Posted: May 31, 2013 - 06:03 PM
Ended up using the eyestrap as the becket. works perfectly. $60 for all parts. not too bad for a H16 downhaul.
Thanks all. -
- Rank: Lubber
- Registered: Dec 16, 2014
- Last visit: Dec 17, 2014
- Posts: 1
Posted: Dec 17, 2014 - 12:11 AM
Ok... the boat unassembled. It took ages and about ten million knocks and hits with a mallet to remove a tramp. No other problems. Shall the next summer be here soon
--
Pass your 70-488 - latest dump exam exams in first try by using our 648-385 - certkiller - braindumps.com wireless bgsp tutorials and best quality www.stevenson.edu dumps along with ccie Loyola University Maryland
--
