I'm considering making trapeze lines from one of the newer synthetic lines.
Which type of line has worked well for anyone?
What type of thimbles did you use aloft at the masthound?
Did you bother with thimbles at the user end or just splice a loop for a mini-block?
What handles worked for you?
All suggestions / thoughts appreciated.
Edited by klozhald on Aug 28, 2013 - 03:30 PM.
--
Sheet In!
Bob
_/)_____/)_/)____/)____/)_____/)/)__________/)__
Prindle 18-2 #244 "Wakizashi"
Prindle 16 #3690 "Pegasus" Sold (sigh)
AZ Multihull Fleet 42 member
(Way) Past Commodore of Prindle Fleet 14
Arizona, USA
--
So if I'm making trapeze lines from Amsteel...
-
- Rank: Chief
- Registered: Apr 19, 2011
- Last visit: Nov 20, 2024
- Posts: 1460
Posted: Aug 28, 2013 - 03:30 PM
-
- Rank: Mate
- Registered: Apr 27, 2011
- Last visit: Dec 13, 2022
- Posts: 163
Posted: Aug 28, 2013 - 04:32 PM
I inherited a setup with spliced loops reinforced with a cover up top and small (3/8" ID) thimbles spliced in at the bottom. T-handle load is taken up by the lower thimble.
Sailed with the setup for 5 regattas this year with no observable wear. So far I really like them.
Line is some flavor of 3/16" dyneema - I'm guessing the Yale Ultrex 12 based on color and feel.
--
Jeff R
'88 H18 "Jolly Mon"
'10 C2 USA1193
NE IN / SE MI
cramsailing.com
-- -
- Rank: Chief
- Registered: Jun 24, 2009
- Last visit: Jun 15, 2023
- Posts: 1555
Posted: Aug 28, 2013 - 05:38 PM
Amsteel would work great, we use it tie safety booms to anchors in front of hydropower plants. Definitely use thimbles and a brummel splice. Also consider getting the top couple of feet where it will be rubbing against the other rigging coated or covered. Seeing wear at the bottom is easy.
--
Dave Bonin
1981 Nacra 5.2 "Lucile"
1986 Nacra 5.7 "Belle"
Winnipeg, Manitoba, Canada
-- -
- Rank: Mate
- Registered: Oct 26, 2002
- Last visit: Sep 23, 2019
- Posts: 390
Posted: Aug 28, 2013 - 09:20 PM
Yeah, wear at the top is the issue. Also consider using sailmaker's thimbles, no sharp edges. -
- Rank: Chief
- Registered: Nov 26, 2009
- Last visit: Aug 10, 2024
- Posts: 2531
Posted: Aug 28, 2013 - 09:48 PM
Do some searches here. There was a thread about a year ago. IIRC the consensus was that they chafe pretty badly at the top.
--
Hobie 18 Magnum
Dart 15
Mystere 6.0XL Sold Was a handful solo
Nacra 5.7
Nacra 5.0
Bombardier Invitation (Now officially DEAD)
Various other Dock cluttering WaterCrap
-- -
- Rank: Mate
- Registered: Apr 15, 2005
- Last visit: Feb 21, 2024
- Posts: 574
Posted: Aug 29, 2013 - 06:58 AM
Then put a cover on them at the top! That is what I am doing, using 7/64" amsteel. I used regular thimbles at the top, the sail makers are much more expensive and I didn't notice better chafe protection with the sail makers thimbles. On the bottom make sure you use a cover when you loop the amsteel through your roller cleat, otherwise it will chafe.
Nearly everyone is using these on the F18 these days. They are stronger, lighter and cheaper than stainless wires.
-Sam -
- Rank: Chief
- Registered: Nov 26, 2009
- Last visit: Aug 10, 2024
- Posts: 2531
Posted: Aug 29, 2013 - 09:35 AM
What life are you getting Sam?
I was going to go this route, but shied away due the threads a while ago regarding chafe near the top. Plus I had a roll of wire sitting in the parts bin, so I remade them with wire, & added a 3:1 height adjuster that came off the wrecked 5.2.
--
Hobie 18 Magnum
Dart 15
Mystere 6.0XL Sold Was a handful solo
Nacra 5.7
Nacra 5.0
Bombardier Invitation (Now officially DEAD)
Various other Dock cluttering WaterCrap
-- -
- Rank: Chief
- Registered: Apr 19, 2011
- Last visit: Nov 20, 2024
- Posts: 1460
Posted: Aug 29, 2013 - 11:51 AM
So instead of terminating the trap wire into a thimble, you are integrating it into a roller cleat, like a clam cleat? What handle did you use above the cleat?
Edited by klozhald on Aug 29, 2013 - 03:46 PM.
--
Sheet In!
Bob
_/)_____/)_/)____/)____/)_____/)/)__________/)__
Prindle 18-2 #244 "Wakizashi"
Prindle 16 #3690 "Pegasus" Sold (sigh)
AZ Multihull Fleet 42 member
(Way) Past Commodore of Prindle Fleet 14
Arizona, USA
--
Users on-line
- 0 users
This list is based on users active over the last 60 minutes.