Installing roller furler on my P16 :: Catamaran Sailboats at TheBeachcats.com

Welcome anonymous guest

Please Support
TheBeachcats.com

Installing roller furler on my P16

mrprindle

Rank: Lubber

Registered: May 05, 2014

Last visit: Jun 17, 2014

Posts: 10
Posted: Jun 17, 2014 - 08:22 PM

Hey guys,

Trying to install my roller furler on the P16. I'm quite newbie at this, so need some help.

Here's the roller furler that came with the boat:

Here's the cord that comes from my jib zip (on the right hand) and an extra cord on the left hand:

Here's me trying something to make it work. As you can see, while it works, it's not very smooth and looks unprofessional ;)

I don't have anything special mounted on the jib halyard. The basic P16 with the ring and the S hook that goes in it,

So what do you guys suggest to make it work on my boat? I've seen many pics, of different boats and technique, but a video would be very helpful for someone that is new to this.

thanks.

Edited by mrprindle on Jun 17, 2014 - 08:22 PM.
the-renovator

Rank: Mate

Registered: Sep 29, 2012

Last visit: Jan 10, 2018

Posts: 441
Posted: Jun 18, 2014 - 06:36 AM

mrprindle, as you may know already, the P16 does not normally have a furling jib, this is a mod done by some to make sailing easier. For the furling jib to work the sail must be attached to the jib wire head and tack using either shackles or cordage, otherwise when the drum spins, the forestay will spin with no furling effect. You have to do away with the prindle setup and go with a furler setup which consists of :-
1) pigtail
2) swivel
3) wire luff (with sail pinned to wire top & bottom)
4) furler drum

only then will you be able to furl the jib, but to get the boat on the water asap, just store the drum and sail with stock setup. I put this mod on both my P16 and my P18 and it is quite complicated as the forestay furler setup has to measure the same length as the stock setup.

http://www.thebeachcats.c…pictures?g2_itemId=88268

This album by edchris might help
Quarath

Rank: Mate

Registered: Jul 06, 2008

Last visit: Jul 19, 2018

Posts: 986
Posted: Jun 19, 2014 - 01:39 PM

Actually you can set a furler on a Prindle with a zippered luff just fine. I have run one on mine for several years. You just have to put the swivel above the upper forestay . I created a shorter upper forestay to compensate for swivel and drum. Jib is not hard mounted to the forestay it goes on like a normal Prindle zippered jib hooked at the top and down hauled at the bottom. The entire system is between swivel and drum though and rotates freely to furl and unfurl.

--
Dustin Finlinson • Magna, UT
Member: Utah Sailing Association
1982 Prindle 18
1986 Hobie 17
1982 Prindle 16
1980 Prindle 16(mostly)
1976 Prindle 16(mostly)
Check out "Prindle Sailors" on Facebook.
--
klozhald

Rank: Chief

Registered: Apr 19, 2011

Last visit: Dec 10, 2024

Posts: 1461
Posted: Jun 19, 2014 - 04:58 PM

QuarathI created a shorter upper forestay to compensate for swivel and drum. Jib is not hard mounted to the forestay it goes on like a normal Prindle zippered jib hooked at the top and down hauled at the bottom. The entire system is between swivel and drum though and rotates freely to furl and unfurl.

This rocks!

--
Sheet In!
Bob
_/)_____/)_/)____/)____/)_____/)/)__________/)__
Prindle 18-2 #244 "Wakizashi"
Prindle 16 #3690 "Pegasus" Sold (sigh)
AZ Multihull Fleet 42 member
(Way) Past Commodore of Prindle Fleet 14
Arizona, USA
--