• mechoption
  
  

  • Rank: Lubber
  • Registered: May 18, 2015
  • Last visit: May 27, 2015
  • Posts: 8

  Posted: May 18, 2015 - 09:55 PM

  Hi all,
  
  Picked up a P16 recently (not sure vintage, but seems to predate mast hinge technology; stepping the mast was brutal) and just got it partially rigged. Quick question on the mast rake, a manual I found online states "Using the main halyard as a plumb, measure the distance from the aft edge of the mast at the black band to the center of the plumb" - I don't have a 'black band' so not sure where to measure from?
  
  Also, is there a simple schematic somewhere that shows how the lines are supposed to run? Particularly the jib as the manual I have talks about an "S" hook I don't seem to have, but I do have some kind of pulley system I haven't figured out yet.
  
  I have lots of monohull experience, but this is my first foray into the catamaran world - looking forward to getting sailing !
  
  

  • 
  •  
• mechoption
  
  

  • Rank: Lubber
  • Registered: May 18, 2015
  • Last visit: May 27, 2015
  • Posts: 8

  Posted: May 18, 2015 - 09:56 PM

  Forgot to add: What do I do with the side stays once the mast rake is set, just reef them on as much as possible?

  • 
  •  
• pbegle
  
  

  • Rank: Mate
  • Registered: Mar 12, 2003
  • Last visit: Feb 19, 2021
  • Posts: 879

  Posted: May 19, 2015 - 11:38 AM

  You have probably '73-75 P-16 with the old mast base & step. Look on the starboard transom for a possible number last of which will be the year. Early jib halyards did not have S hook, but had wire luff jib like H-16. Actually easier to raise jib--be sure to use 3:1 near base of mast and pull it tight. Where are you located? Pete

  • 
  •  
• mechoption
  
  

  • Rank: Lubber
  • Registered: May 18, 2015
  • Last visit: May 27, 2015
  • Posts: 8

  Posted: May 21, 2015 - 10:22 PM

  Indeed, ends in "76" :) Looks like the jib will 3:1 on the mast - there's remnants of a pulley on the base of the mast, I thought it was for a main downhaul but perhaps it's for the jib halyard. I'm hoping to rig this Sunday (although Striker Casting hasn't shown up in the mail yet, and I think I need one!) and take pictures of the parts I'm not so sure about.
  
  I'm located up the Ottawa Valley, few hours from Ottawa.

  • 
  •  
• pbegle
  
  

  • Rank: Mate
  • Registered: Mar 12, 2003
  • Last visit: Feb 19, 2021
  • Posts: 879

  Posted: May 22, 2015 - 12:07 AM

  If you do not have the flanged mast base casting & hinge, they are available from Murrays as are mast head pulleys. Pete

  • 
  •  
• mechoption
  
  

  • Rank: Lubber
  • Registered: May 18, 2015
  • Last visit: May 27, 2015
  • Posts: 8

  Posted: May 24, 2015 - 10:44 PM

  First sail was a blast !!! Although, apparently too much as I washed out the rubber stopper under the rear cross bar (pic below). Does this hole allow full access to the hull (i.e., if it submerges do I fill my hull up?)? I put my hand in and seems to be just a pocket but I'm not sure. I see murrays have plugs (which look quite different to what came out of mine), but any suggestions for alternates I could get from a hardware store? Duct tape?
  
  

  • 
  •  
• pbegle
  
  

  • Rank: Mate
  • Registered: Mar 12, 2003
  • Last visit: Feb 19, 2021
  • Posts: 879

  Posted: May 25, 2015 - 12:10 PM

  Yes, duct tape good as anything. Send a pic of your mast step (on front xbar). Pete

  • 
  •  
• mechoption
  
  

  • Rank: Lubber
  • Registered: May 18, 2015
  • Last visit: May 27, 2015
  • Posts: 8

  Posted: May 27, 2015 - 07:31 PM

  Here's a pic of the mast step. What is the thing circled in red in the 2nd pic for? You may also notice my wooden striker casting; new one should be arriving soon from Murrays :)
  
  

  • 
  •  
• nacra55
  
  

  • Rank: Mate
  • Registered: Nov 02, 2004
  • Last visit: Aug 07, 2023
  • Posts: 626

  Posted: May 27, 2015 - 07:48 PM

  The thing circled in red is a base for a swivel cam cleat. It looks like someone tried to move the Jib sheet cleats to the main beam like on a Hobie 16.
  
  --
  Ron
  Nacra F18
  Reservoir Sailing Assn.
  Brandon, Mississippi
  --

  • 
  •  
• pbegle
  
  

  • Rank: Mate
  • Registered: Mar 12, 2003
  • Last visit: Feb 19, 2021
  • Posts: 879

  Posted: May 28, 2015 - 11:15 PM

  The swivel cam cleat was for a barbor hauler system to pull the jib leads outboard when sailing on a broad reach. Reason I wanted the pic was to see that your mast step will not accept a hinge. I have the later model mast step that will accept the hinge including the striker rod if you're interested. Text for pic. Pete 909-800-5237

  • 
  •  
• Wolfman
  
  

  • Rank: Chief
  • Registered: Jun 24, 2009
  • Last visit: Jun 15, 2023
  • Posts: 1555

  Posted: May 30, 2015 - 02:03 PM

  Great stuff nice to have another Canadian here! The prindle manuals are located here: http://www.thebeachcats.com/pictures?g2_itemId=75669
  
  Take pete up on his offer if you can. He can hook you up with everything you need for the old boat. He has helped me out on quite a few parts.
  
  If you want a more permanent fix for the hole you can probably find something at the hardware store that will work and then caulk it in place. Heck even a big tapered cork.
  
  --
  Dave Bonin
  1981 Nacra 5.2 "Lucile"
  1986 Nacra 5.7 "Belle"
  Winnipeg, Manitoba, Canada
  --

  • 
  •  
•  
•  

Users on-line

• SC19

This list is based on users active over the last 60 minutes.