--
J.D.
1981 Prindle 16
1978 Y-Flyer
Akron,OH
USA
--
1981 Prindle 16 rigging question
-
- Rank: Lubber
- Registered: Jun 14, 2015
- Last visit: Jul 19, 2016
- Posts: 16
Posted: Jun 14, 2015 - 10:30 PM
I purchased used Prindle 16 few weeks ago and cannot determine correct traveler line size? Previous owner said he never moved the traveler..the current set-up is a mess.The on-line Prindle manual is not clear to me pic. Please share any pics of your set-up. Any suggestions will be greatly appreciated.
--
J.D.
1981 Prindle 16
1978 Y-Flyer
Akron,OH
USA
-- -
- Rank: Mate
- Registered: Mar 12, 2003
- Last visit: Feb 19, 2021
- Posts: 879
Posted: Jun 14, 2015 - 10:39 PM
7/16 or 3/8 works well. Start by going thru the jam cleat, then thru traveler car, then tie off on eyestrap on middle rear of crossbeam. You could use end of mainsheet unless it's 1/2" then get rid of it as 1/2" promotes capsize. Pete -
- Rank: Lubber
- Registered: Jun 14, 2015
- Last visit: Jul 19, 2016
- Posts: 16
Posted: Jun 14, 2015 - 10:46 PM
Sounds good, thanks for the quick reply!
--
J.D.
1981 Prindle 16
1978 Y-Flyer
Akron,OH
USA
-- -
- Rank: Chief
- Registered: Apr 19, 2011
- Last visit: Dec 10, 2024
- Posts: 1461
Posted: Jun 15, 2015 - 04:35 PM
I used 5/16" line tied to the end of my mainsheet. Like 3/8, it travels much easier through the traveler car. Be sure you use a good knot, like a double sheet bend set tightly, and allow the knots' location to stop your traveler car before it strikes the crossbar bolt at the end when you travel out to the max.
Edited by klozhald on Jun 15, 2015 - 04:39 PM.
--
Sheet In!
Bob
_/)_____/)_/)____/)____/)_____/)/)__________/)__
Prindle 18-2 #244 "Wakizashi"
Prindle 16 #3690 "Pegasus" Sold (sigh)
AZ Multihull Fleet 42 member
(Way) Past Commodore of Prindle Fleet 14
Arizona, USA
-- -
- Rank: Lubber
- Registered: Jun 14, 2015
- Last visit: Jul 19, 2016
- Posts: 16
Posted: Jun 15, 2015 - 09:57 PM
Good stuff, I will make the line changes tomorrow. The traveler is next on the list of upgrades.
I really appreciate the responses.
--
J.D.
1981 Prindle 16
1978 Y-Flyer
Akron,OH
USA
-- -
- Rank: Mate
- Registered: Mar 12, 2003
- Last visit: Feb 19, 2021
- Posts: 879
Posted: Jun 15, 2015 - 11:04 PM
If the rollers are broken on traveler, it will jam on wrong side during a jibe & flip you. New ones are $80 but will last life of the boat. Pete -
- Rank: Lubber
- Registered: Jun 14, 2015
- Last visit: Jul 19, 2016
- Posts: 16
Posted: Jun 15, 2015 - 11:36 PM
The rollers are in poor shape. I was checking out a shiney new traveler on Murrays. Looks like 80$ and worth it. I hope to get in a sail this week too see how everything else is working. Thx.
--
J.D.
1981 Prindle 16
1978 Y-Flyer
Akron,OH
USA
-- -
- Rank: Chief
- Registered: Apr 19, 2011
- Last visit: Dec 10, 2024
- Posts: 1461
Posted: Jun 16, 2015 - 07:48 PM
It is. You will have to remove the end cap from your crossbar to replace it. Since they are not structural rivets, they need not be Monel, but they are big ones and I can't remember if its two or three.
For the record, pbegle has all kinds of used Prindle parts, and decades of experience sailing them.
[I didn't say how old, Pete! (I think he's younger than me...)]
--
Sheet In!
Bob
_/)_____/)_/)____/)____/)_____/)/)__________/)__
Prindle 18-2 #244 "Wakizashi"
Prindle 16 #3690 "Pegasus" Sold (sigh)
AZ Multihull Fleet 42 member
(Way) Past Commodore of Prindle Fleet 14
Arizona, USA
-- -
- Rank: Lubber
- Registered: Jun 14, 2015
- Last visit: Jul 19, 2016
- Posts: 16
Posted: Jun 17, 2015 - 09:42 PM
i just looked at the end cap and noticed 4 rivets. Any trick to remove??
--
J.D.
1981 Prindle 16
1978 Y-Flyer
Akron,OH
USA
-- -
- Rank: Mate
- Registered: Mar 12, 2003
- Last visit: Feb 19, 2021
- Posts: 879
Posted: Jun 17, 2015 - 10:45 PM
More than decades, Bob, almost a century!!! I never take the 4 rivets out, but simply grind off the 1 1/4" of stop off & trim the traveler end. If you have an extra stainless washer, put it under bolt head to raise it a little when putting it back. Pete -
- Rank: Lubber
- Registered: Jun 14, 2015
- Last visit: Jul 19, 2016
- Posts: 16
Posted: Jun 17, 2015 - 10:54 PM
You just saved me hours of research on type & size (thickness) of rivets. Many thanks!
--
J.D.
1981 Prindle 16
1978 Y-Flyer
Akron,OH
USA
-- -
- Rank: Lubber
- Registered: Dec 27, 2016
- Last visit: May 24, 2019
- Posts: 57
Posted: Dec 27, 2016 - 03:16 PM
Have a p15. How would you rig the lines for an added jib?
Thanks Frank
--
Frank
Prindle 15/Hobie 16/Hobie 14T
--
