I posted this over at Hobie. Please let me know if you have any thoughts
http://www.hobiecat.com/f…ewtopic.php?f=14&t=55330
Thanks!
--
Ted
Hobie 16
South Carolina Lake sailing
--
Hobie 16 mast has water
-
- Rank: Mate
- Registered: May 31, 2011
- Last visit: Dec 17, 2023
- Posts: 126
Posted: Jul 17, 2015 - 11:59 AM
-
- Rank: Mate
- Registered: Apr 22, 2015
- Last visit: May 21, 2023
- Posts: 484
Posted: Jul 17, 2015 - 12:56 PM
If you think you have a leak, this plug with sealant stuffed in both ends of the mast is very effective:
http://www.murrays.com/50-20060000.html
--
Hobie 16 (3 formerly)
MacGregor 25 (formerly)
Chrysler Dagger 14 (formerly)
NACRA 5.0 (currently)
High Point, NC
-- -
- Rank: Mate
- Registered: Feb 18, 2013
- Last visit: Jul 19, 2015
- Posts: 396
Posted: Jul 17, 2015 - 08:52 PM
You might already know this but you might get the water out of the mast before you plug it. After the mast is sealed there's probably no difference which way it is stowed while towing.
--
Goodsailing
Laser-Standard Rig (Sold 6/15)
H18 (Sold 7/15)
Building 19' Tacking Outrigger
Balt-Wash Area
-- -
- Rank: Mate
- Registered: Aug 01, 2002
- Last visit: Sep 14, 2024
- Posts: 425
Posted: Jul 18, 2015 - 11:10 AM
I don't have any recommendations for the leak other than the standard submerge, look for bubbles, drain, and seal procedures.....lots of threads on the Hobie forums in that regard. I'd seriously doubt the water has caused any internal corrosion issue. May be obvious, but, for trailering, I always flip the mast so that the luff track is up. If the mast crutch padding is inadequate, the rubbing can cause damage to the aluminum part of the track (happened to me). This way there's a lot less stress on the plastic portion of the luff track on the comp tip as well.
--
Jerome Vaughan
Hobie 16
Clinton, Mississippi
-- -
- Rank: Mate
- Registered: May 31, 2011
- Last visit: Dec 17, 2023
- Posts: 126
Posted: Jul 18, 2015 - 07:54 PM
Thanks Rattlenhum. The luff track issue was my main concern regarding the orientation.
Does anyone have any recommendations for 'crutch padding'? I use a throwable life peserver on the back, and a cloth on the hard V in the front.
--
Ted
Hobie 16
South Carolina Lake sailing
-- -
- Rank: Mate
- Registered: Feb 18, 2013
- Last visit: Jul 19, 2015
- Posts: 396
Posted: Jul 19, 2015 - 11:17 AM
Pool noodle foam wrapped with section of car inner tube/ zip tied on inside of "V." Track down, no problem. Winch line wrapped around a few times and clipped to loop near mast step to keep mast secured tight to "V"
--
Goodsailing
Laser-Standard Rig (Sold 6/15)
H18 (Sold 7/15)
Building 19' Tacking Outrigger
Balt-Wash Area
-- -
- Rank: Mate
- Registered: Nov 02, 2004
- Last visit: Aug 07, 2023
- Posts: 626
Posted: Jul 19, 2015 - 12:42 PM
I use a scrap of carpet up front. A nice berber or medium shag. No preference on color.
--
Ron
Nacra F18
Reservoir Sailing Assn.
Brandon, Mississippi
-- -
- Rank: Lubber
- Registered: Nov 27, 2014
- Last visit: Jun 17, 2017
- Posts: 8
Posted: Jul 25, 2015 - 02:54 PM
I carry my mast track-down. The trailer crutch has rubber pads which support the sides in a sort of V configuration, and at the rear I use the Hobie thingy which doesn't seem to put any pressure on the track. I want the track down so the tie-down straps don't push on it.,
