Jib line snagging
-
- Rank: Lubber
- Registered: Jun 30, 2012
- Last visit: Jul 29, 2024
- Posts: 61
Posted: Jul 03, 2016 - 08:39 AM
My jib line is getting snagged on mast base , downhaul cleats and anything else around mast base. Drives me crazy in higher winds as i am halfway through a tack !! It is a Prindle 19 , Is there something missing on my setup? -
- Rank: Chief
- Registered: Nov 26, 2009
- Last visit: Aug 10, 2024
- Posts: 2531
Posted: Jul 03, 2016 - 08:55 AM
Do you have a preventer?
Run a piece of 1/4" bungee from the outside of the front beam-through the bottom of the diamond wires-over to the far side of the beam.
That will deflect the jib blocks/sheet away from the mast base/cleat
--
Hobie 18 Magnum
Dart 15
Mystere 6.0XL Sold Was a handful solo
Nacra 5.7
Nacra 5.0
Bombardier Invitation (Now officially DEAD)
Various other Dock cluttering WaterCrap
-- -
- Rank: Lubber
- Registered: Jan 08, 2007
- Last visit: Mar 23, 2023
- Posts: 49
Posted: Jul 03, 2016 - 12:11 PM
+1 Had 18' Prindle with same issues. An extra piece of trap bungee solved the problem.
--
Forrest
I-20 USA-645
Hernando, Florida
"There's not enough rum in the drum"
-- -
- Rank: Lubber
- Registered: Jun 30, 2012
- Last visit: Jul 29, 2024
- Posts: 61
Posted: Jul 03, 2016 - 09:53 PM
I will set that up.. thanks for the help -
- Rank: Chief
- Registered: Nov 26, 2009
- Last visit: Aug 10, 2024
- Posts: 2531
Posted: Jul 03, 2016 - 11:47 PM
A pictures worth a thousand words. This is not my cat, i just cribbed the photo from one of the albums.
You can clearly see the preventer, looks like an inverted "V".
Click the photo to see full size
Edited by Edchris177 on Jul 03, 2016 - 11:57 PM.
--
Hobie 18 Magnum
Dart 15
Mystere 6.0XL Sold Was a handful solo
Nacra 5.7
Nacra 5.0
Bombardier Invitation (Now officially DEAD)
Various other Dock cluttering WaterCrap
-- -
- Rank: Lubber
- Registered: Jul 28, 2014
- Last visit: Jan 12, 2018
- Posts: 13
Posted: Jul 04, 2016 - 01:06 PM
If you have a mast rotator, the jib sheet might still get snagged with the preventer rigged as shown in the picture submitted by Edchris. I solved this by running the ends of the bungee forward and outboard to the the bridle foil tangs. You can make a simple attachment using using small diameter line looped around the tang and add plastic clips to the bungee ends.
--
Kip
NACRA 5.8na
Chesapeake, VA
-- -
- Rank: Master Chief
- Registered: Jun 20, 2006
- Last visit: May 22, 2024
- Posts: 7089
Posted: Jul 05, 2016 - 08:47 AM
a single bungee attached under the jib furler (if there is one), or similar location and the other end connected to the mast will have the same results
Users on-line
- 0 users
This list is based on users active over the last 60 minutes.