Viking inspection port o-ring measures
-
- Rank: Mate
- Registered: Aug 18, 2003
- Last visit: Dec 13, 2023
- Posts: 880
Posted: Dec 04, 2018 - 09:10 AM
Hi, I need to replace the o-rings of 4" Viking Marine inspection ports, they are out of stock at Murrays and didn't find them elsewhere. Anybody has measured the o-ring diameter and section, to find an alternative? I'm away from my boat, Thanks -
- Rank: Mate
- Registered: Sep 01, 2002
- Last visit: Oct 31, 2024
- Posts: 796
Posted: Dec 04, 2018 - 09:54 AM
Did you try Annapolis Performance Sailing
--
John Schwartz
Ventura, CA
-- -
- Rank: Mate
- Registered: Mar 19, 2004
- Last visit: Nov 21, 2024
- Posts: 964
Posted: Dec 04, 2018 - 12:14 PM
-
- Rank: Mate
- Registered: Aug 18, 2003
- Last visit: Dec 13, 2023
- Posts: 880
Posted: Dec 04, 2018 - 03:53 PM
I read they dont make them anymore (and i believe what i read on the internet...)
Found some here, in Switzerland, and ordered the 6 units they had in stock.
https://www.h2o-sensations.com
I live in Chile, so not too different than ordering from the U.S.
Interesting site, i got some other stuff too
Edited by Andinista on Dec 04, 2018 - 03:55 PM. -
- Rank: Mate
- Registered: Nov 18, 2005
- Last visit: Apr 19, 2024
- Posts: 236
Posted: Dec 04, 2018 - 08:33 PM
Go to McMaster Carr, buy some linear o-ring stock, cut and glue the ends together. Very easy and no need to chase down a Viking specific o-ring.
--
dk
Blade F-16
Hobie 14
Corsair F-242
Mirage 25 (Sold)
Hobie Tiger (Sold)
Hobie Tiger (Sold)
TomCat 6.2 (Sold)
-- -
- Rank: Mate
- Registered: Sep 01, 2002
- Last visit: Oct 31, 2024
- Posts: 796
Posted: Dec 05, 2018 - 12:37 PM
I was going to recommend Granger of The O-Ring Store.... but I saw that APS had them.. all you need are the measurements...
--
John Schwartz
Ventura, CA
-- -
- Rank: Mate
- Registered: Apr 22, 2015
- Last visit: May 21, 2023
- Posts: 484
Posted: Dec 12, 2018 - 12:22 PM
Here is what I use. I purchase them at a local industrial supply house, buna, and replace them every year. As a tip, when you're not sailing, loosen them a bit so that they're not compressed all the time and loose memory/seal. Also inspect and clean them periodically, sand/dirt etc. doesn't make fot a good seal:
https://www.bestpartsonli…/product&product_id=5143
Edited by leeboweffect on Dec 12, 2018 - 01:22 PM.
--
Hobie 16 (3 formerly)
MacGregor 25 (formerly)
Chrysler Dagger 14 (formerly)
NACRA 5.0 (currently)
High Point, NC
-- -
- Rank: Mate
- Registered: Apr 22, 2015
- Last visit: May 21, 2023
- Posts: 484
Posted: Dec 12, 2018 - 12:35 PM
One of the die makers at Viking had a bit of fun one afternoon...
--
Hobie 16 (3 formerly)
MacGregor 25 (formerly)
Chrysler Dagger 14 (formerly)
NACRA 5.0 (currently)
High Point, NC
--
Users on-line
- 0 users
This list is based on users active over the last 60 minutes.