Wondering if anyone has tips for shaping a sq top mainsail for a Nacra 5.2. The mast wants to bend to the shape of the original Dacron main sail luff, whereas the Slo Sail square top is a much straighter cut along the luff. So in a close haul, even with tight diamond wires, the top third of the mast (beyond the diamond wires) bends a bit. Are people compensating by not rotating the mast as much?
--
***********************
Pairajacks
1985 Nacra 5.2
Corvallis Oregon
************************
--
Square Top Mainsail, Shaping with less Mast Bend
-
- Rank: Lubber
- Registered: May 11, 2011
- Last visit: May 31, 2019
- Posts: 37
Posted: May 26, 2019 - 01:55 PM
-
- Rank: Chief
- Registered: Apr 19, 2011
- Last visit: Sep 25, 2024
- Posts: 1459
Posted: May 28, 2019 - 12:45 PM
Compared to how tight the diamond wires were under a soft rig, are the wires now scary tight?
Are they tight enough to clearly see aft pre-bend in the mast without your sail up?And you moved your spreaders significantly aft?
Yes, most cats with pre-bend use less rotation successfully.
Hopefully you'll get a more specific response on the 5.2 from the NACRA members here.
Bob
--
Sheet In!
Bob
_/)_____/)_/)____/)____/)_____/)/)__________/)__
Prindle 18-2 #244 "Wakizashi"
Prindle 16 #3690 "Pegasus" Sold (sigh)
AZ Multihull Fleet 42 member
(Way) Past Commodore of Prindle Fleet 14
Arizona, USA
-- -
- Rank: Master Chief
- Registered: Jun 20, 2006
- Last visit: May 22, 2024
- Posts: 7089
Posted: May 28, 2019 - 02:07 PM
sails are typically cut to follow the mast/prebend
Edited by MN3 on May 28, 2019 - 11:22 PM. -
- Rank: Lubber
- Registered: Jul 05, 2018
- Last visit: Jul 06, 2023
- Posts: 63
Posted: May 28, 2019 - 07:01 PM
I have a 5.5 SL with square top. Following the sail makers recommendations (Skip E). I set up for prebend.
1.5 to 1.75 inch spreader rake with 1 inch of prebend. The mast seems to be working fine with the sail. -
- Rank: Lubber
- Registered: Jul 05, 2018
- Last visit: Jul 06, 2023
- Posts: 63
Posted: May 28, 2019 - 07:02 PM
I have a 5.5 SL with square top. Following the sail makers recommendations (Skip E). I set up for prebend.
1.5 to 1.75 inch spreader rake with 1 inch of prebend. The mast seems to be working fine with the sail. -
- Rank: Mate
- Registered: Nov 02, 2004
- Last visit: Aug 07, 2023
- Posts: 626
Posted: May 28, 2019 - 07:42 PM
That's the same numbers Skip recommended for the stock pin head main on the 5.5 SL.
I think it was 550 lbs on the loose gauge.
--
Ron
Nacra F18
Reservoir Sailing Assn.
Brandon, Mississippi
-- -
- Rank: Lubber
- Registered: May 11, 2011
- Last visit: May 31, 2019
- Posts: 37
Posted: May 30, 2019 - 12:42 AM
To answer klozhald, i could probably try to tighten up the diamond wire a little more. Im just not expecting much benefit because much of the bend occurs above the diamond attachment...about a third is above the diamond. Note that this is a new square top main sail that wasnt part of the original equipment. My 1985 nacra 5.2 has a straight post for the diamond..theres no rake. I would like to hear from some of the nacra folks starting to experiment with sq tops on their boats.
--
***********************
Pairajacks
1985 Nacra 5.2
Corvallis Oregon
************************
-- -
- Rank: Mate
- Registered: Jun 17, 2011
- Last visit: Sep 24, 2023
- Posts: 783
Posted: May 30, 2019 - 01:09 PM
The way a modern rig works is that the sale has extra luff curve compared to the pre-bend of the mast. In your case the mast is straight and the square top has a little bit of curve to it which will give it some extra girth. When you apply downhaul or Main sheet the mast will start to bend, and the sail will flatten out. Eventually the mast bend will be great enough the sail is as flat as a pancake. So when I sail my A-cat I now consider myself manipulating the mast to control the shape of the sail as an integral part of the rig.
It’s not shocking at all to me that the mast will behave quite a bit differently with the new square top presumably made of modern laminate materials compared to a 30-year-old Nacra sail. It sounds to me like the mast is bending to flatten out your sail while you’re sailing in upwind. That sounds quite normal to me. So in my conclusion I’m not sure that you have a problem? Unless you have something else going on here?
Edited by bacho on May 30, 2019 - 01:10 PM.
--
Greenville SC
Offering sails and other go fast parts for A-class catamarans
-- -
- Rank: Lubber
- Registered: May 11, 2011
- Last visit: May 31, 2019
- Posts: 37
Posted: May 31, 2019 - 09:11 PM
The question is what happens when your mast bends far beyond the point where the sail flattens out. My unerstanding is that if the cut of the main is 3 inches off vertical at the top, then the mast bend to flatten the sail would be 3 inches. What happens to the sail performance when your mast too easily bends to 8 inches?
--
***********************
Pairajacks
1985 Nacra 5.2
Corvallis Oregon
************************
-- -
- Rank: Chief
- Registered: Apr 19, 2011
- Last visit: Sep 25, 2024
- Posts: 1459
Posted: Jun 03, 2019 - 07:13 PM
If I may paraphrase Bacho, your mast is doing what your sail is telling it to, through the cut of the material, and controls like downhaul and the mainsheet.
If it doesn't look or feel right to you, this is the conversation to have with your sailmaker.
Send or bring pictures.
--
Sheet In!
Bob
_/)_____/)_/)____/)____/)_____/)/)__________/)__
Prindle 18-2 #244 "Wakizashi"
Prindle 16 #3690 "Pegasus" Sold (sigh)
AZ Multihull Fleet 42 member
(Way) Past Commodore of Prindle Fleet 14
Arizona, USA
-- -
- Rank: Master Chief
- Registered: Jun 20, 2006
- Last visit: May 22, 2024
- Posts: 7089
Posted: Jun 04, 2019 - 12:29 PM
wouldn't this be in direct relation to the amount of downhaul you set?
couldn't you just reduce the amount of downhaul? -
- Rank: Mate
- Registered: May 10, 2016
- Last visit: Oct 22, 2024
- Posts: 226
Posted: Jun 04, 2019 - 01:31 PM
When too much (or too little) mast bend occurs you are at less than optimum trim for that given mainsail shape. There would have to be some force applied to make the mast bend past the cut of the luff curve. This could be any combination of diamond wires, downhaul (cunningham), Mainsheet, or even too much rig tension. -
- Rank: Mate
- Registered: Jun 17, 2011
- Last visit: Sep 24, 2023
- Posts: 783
Posted: Jun 05, 2019 - 10:10 AM
There is a little more to it than simply the luff curve. You’re also pulling back on the mast which opens up the leech at the same time.
--
Greenville SC
Offering sails and other go fast parts for A-class catamarans
-- -
- Rank: Mate
- Registered: Mar 19, 2004
- Last visit: Jul 09, 2024
- Posts: 963
Posted: Jun 05, 2019 - 12:15 PM
What happens is the leech will open up and the top of the sail will twist off to leeward. This can be a good thing to some degree since a flat and twisted sail has a lower center of effort and reduced drag, so good in high wind applications. The problem is that if the mast bends too easily, the top of the sail will twist open in light wind reducing power and hurting your upwind performance.
sm -
- Rank: Mate
- Registered: Apr 15, 2005
- Last visit: Feb 21, 2024
- Posts: 574
Posted: Jun 05, 2019 - 12:28 PM
And that is why modern rigs are far stiffer side-side then old rigs. More power and more tunable. The 5.2 rig is like a wet noodle in comparison. Increasing diamond wire tension may help but has limited impact on the top 1/3rd of the rig above where the wires stop.
Users on-line
This list is based on users active over the last 60 minutes.