Adhesive for Non-Skid
-
- Rank: Lubber
- Registered: Mar 14, 2018
- Last visit: May 15, 2021
- Posts: 22
Posted: May 10, 2021 - 11:15 PM
I have a roll of nonskid (the rubber kind) that I found sitting in the sail box of my cat when I bought it. It was a kit from Murays, about 3" wide for the edge of the NACRA hull. There is a can of contact cement in there but I'm sure that's well beyond its prime but the rubber seems fine (at least far better than what is on the boat now) What would you guys recommend for sticking it on. I'm looking for something that won't be a pain in the ass to remove when that time eventually comes. -
- Rank: Mate
- Registered: Apr 07, 2017
- Last visit: Dec 14, 2024
- Posts: 369
Posted: May 11, 2021 - 07:43 AM
I've always used a rubber non- skid tape purchased at West Marine. Lasts a few years then clean with acetone and replace. The other stuff is a lot of work to clean off the old glue. However, the last time I did this I went sailing before I replaced the non-n skid and discovered that with good rubber soled shoes there was no problem. Probably not so good barefoot. Also my boat is 35 years old and the surface where the non-skid would be is not all that slippery and not waxed.
--
Bill Townsend
G-Cat 5.0
Sarasota
-- -
- Rank: Chief
- Registered: Apr 19, 2011
- Last visit: Dec 10, 2024
- Posts: 1461
Posted: May 11, 2021 - 01:03 PM
Your non-skid is probably neoprene, and the two things that break it down are the sun and salty sweat. If you put it on you must keep it out of sunlight. No matter what adhesive you use, it is unpleasant to get it off because you will wait until it begins to crumble to want it off.
Consider not using it.
Instead use Re-Dek rom Murray's. It's a liquid that rolls on clear, lasts a long time and is used by SUP boarders because it is durable and can be sanded down and reapplied. I have it on my Prindle from the transom, forward to 2 feet in front of the front crossbar. I put it that far forward because when I stuff a hull in the back of a wave and my crew goes forward they still have some grip in front of the crossbar to help them regain their footing and position.
My $0.02.
Edited by klozhald on May 11, 2021 - 12:05 PM.
--
Sheet In!
Bob
_/)_____/)_/)____/)____/)_____/)/)__________/)__
Prindle 18-2 #244 "Wakizashi"
Prindle 16 #3690 "Pegasus" Sold (sigh)
AZ Multihull Fleet 42 member
(Way) Past Commodore of Prindle Fleet 14
Arizona, USA
-- -
- Rank: Mate
- Registered: Jun 30, 2018
- Last visit: Dec 15, 2024
- Posts: 598
Posted: May 11, 2021 - 02:31 PM
How well does self-adhesive EVA foam deck hold up? Can get approximately 3' by 8' for $100 on-line, but that could be real "expensive" if you have to remove it after 2 years...
--
Chuck C
NACRA 500 Mk2
Hobie 21se (sold)
-- -
- Rank: Mate
- Registered: Oct 20, 2011
- Last visit: Apr 03, 2023
- Posts: 167
Posted: May 11, 2021 - 02:54 PM
I have adhesive backed Eva foam on my sunfish deck to hide a spider cracked area that I repaired, but didn’t want to gel coat.
It has held up over 3 years now and no sign of deterioration. Stored outside, no cover.
--
Supercat 15
Windrider 17
Several Sunfish and Sunfish clones
Ratboat built from Zuma and Sunfish parts
Shallow water sailor in the Delaware Bay
-- -
- Rank: Lubber
- Registered: Mar 14, 2018
- Last visit: May 15, 2021
- Posts: 22
Posted: May 11, 2021 - 09:27 PM
So does anyone have an idea of what adhesive to use? I realize this is probably not the best non-skid ever but it's what I have and since I'm likely going to sell the boat or completely refinish the hulls in a season or so it's silly to spend the money on expensive stuff now that will be ripped up later.
Is 4200 the way to go or too aggressive/hard to remove?
Edited by thebda on May 11, 2021 - 09:45 PM. -
- Rank: Lubber
- Registered: Aug 26, 2020
- Last visit: Mar 21, 2022
- Posts: 34
Posted: May 11, 2021 - 11:02 PM
I’ve used weldwood contact cement for installing Eva foam, and “hydro turf” Mats on jet skis in the past.
Planning on using it again to add some padded traction/seating on N5.7.
Brush it on, wait for it to tack, and start sticking. Definitely requires sanding to remove it though.
Edited by jd91t on May 11, 2021 - 11:06 PM. -
- Rank: Mate
- Registered: Jun 17, 2011
- Last visit: Sep 24, 2023
- Posts: 783
Posted: May 12, 2021 - 03:25 AM
The psa backed turf is superior IMO. I have had to deal with removing contact cement a few times now. It sucks big time. It is the proper glue to use though,
For durability on the turf, I replaced mine on the A cat after 5 years. The lighter colors seem to get killed by UV faster than dark. I had a boat with dark blue and dark grey that is doing fine after 7? Years.
--
Greenville SC
Offering sails and other go fast parts for A-class catamarans
-- -
- Rank: Lubber
- Registered: Mar 14, 2018
- Last visit: May 15, 2021
- Posts: 22
Posted: May 15, 2021 - 11:06 AM
Guess it sounds like there are no good solutions for something you'll remove in a season and replace with better, maybe I'll just see if the stuff I've got holds out for another season and go from there. -
- Rank: Mate
- Registered: Feb 05, 2011
- Last visit: Jun 15, 2021
- Posts: 575
Posted: May 15, 2021 - 05:46 PM
https://www.boatcarpetcen…m/small-boat-carpet-glue
I used a product like this to adhere outdoor carpet to the cradles on my trailer.
--
'82 Super Cat 15
Hull #315
Virginia
Previously owned: '70 H14, '79 H16, '68 Sailmaster 26, '85 H14T
--
Users on-line
- 0 users
This list is based on users active over the last 60 minutes.