Video of my H18 and some

Video of my H18 and some "improvements" for lake sailing.

timscottyoung

Rank: Lubber

Registered: Sep 23, 2012

Last visit: Sep 20, 2022

Posts: 57
Posted: Sep 17, 2021 - 03:18 PM

https://virtustube-my.sha…r_-v-rTudWWSvVQ?e=PoJUU8

--
Tim Young
Hobie 18' + other stuff that floats and goes.
Kentucky
--
MN3

Rank: Master Chief

Registered: Jun 20, 2006

Last visit: May 22, 2024

Posts: 7089
Posted: Sep 17, 2021 - 03:51 PM

nice mods!
where did you get the pins or did you build them yourself?
charlescarlis

Rank: Mate

Registered: Jun 30, 2018

Posts: 593
Posted: Sep 17, 2021 - 08:38 PM

Nice! Yes, please- details on the pins, size tubing, etc. That's looking like a must try. Sa-lick.

--
Chuck C
NACRA 500 Mk2
--
waiex191

Rank: Mate

Registered: Oct 07, 2020

Last visit: Feb 29, 2024

Posts: 359
Posted: Sep 17, 2021 - 10:22 PM

Cool. Would like to see pictures of your house boat machine shop. Is that in the basement?

--
Bryan in Poplar Grove, IL
Supercat 17, unknown year. Future project
Hobie 16, 1977 - died a spectacular death https://youtu.be/Y7O22bp2MVA
Hobie 16, 1978 - current boat
--
baycatsocnj

Rank: Lubber

Registered: May 08, 2019

Last visit: Sep 19, 2021

Posts: 3
Posted: Sep 19, 2021 - 09:49 AM

You should showcase this on JoyriderTV! (Youtube)...unless you already have. This is an interesting setup!
timscottyoung

Rank: Lubber

Registered: Sep 23, 2012

Last visit: Sep 20, 2022

Posts: 57
Posted: Sep 20, 2021 - 12:24 PM

MN3nice mods!
where did you get the pins or did you build them yourself?

Rudder Pins - Built from scratch -
https://virtustube-my.sha…FVtvqLTtetL7n-Q?e=YWsmC9

The only thing I would do differently is mill 2 slots instead of a long continuous slot. The hole size for the roll pins would need to be enlarged. I started out planning to drill and tap those holes and use SS Shoulder Bolts, but drilling and tapping SS with a tiny tap wasn't working out. So I over-drilled the hole and drove in the roll pins, which work fine. Note that these roll pins are to be driven in while the rudder pin assy. is installed on the boat. Once the roll pins are driven in, the rudder pin assy. cannot be removed, which is what I wanted. If you NEED to remove the rudder pin assy., you can grab the roll pins with vise grips and pinch and pull.

--
Tim Young
Hobie 18' + other stuff that floats and goes.
Kentucky
--
timscottyoung

Rank: Lubber

Registered: Sep 23, 2012

Last visit: Sep 20, 2022

Posts: 57
Posted: Sep 20, 2021 - 12:28 PM

waiex191Cool. Would like to see pictures of your house boat machine shop. Is that in the basement?

Haha... I have some basic tools at the houseboat, but I used the Milling machine where I work for the slot and did the rest at home with basic metalworking tools. The "basement" of the houseboat is full of holding tanks, HVAC, water heater, etc.

--
Tim Young
Hobie 18' + other stuff that floats and goes.
Kentucky
--
MN3

Rank: Master Chief

Registered: Jun 20, 2006

Last visit: May 22, 2024

Posts: 7089
Posted: Sep 20, 2021 - 03:12 PM

QuoteHaha... I have some basic tools at the houseboat, but I used the Milling machine where I work for the slot and did the rest at home with basic metalworking tools. The "basement" of the houseboat is full of holding tanks, HVAC, water heater, etc.

Do you have an online order page? I would like 2 sets please and perhaps 1 spare
thanks! :)
waiex191

Rank: Mate

Registered: Oct 07, 2020

Last visit: Feb 29, 2024

Posts: 359
Posted: Sep 20, 2021 - 04:20 PM

I'd like to see some video of the drill propulsion system in action. That is very clever.

--
Bryan in Poplar Grove, IL
Supercat 17, unknown year. Future project
Hobie 16, 1977 - died a spectacular death https://youtu.be/Y7O22bp2MVA
Hobie 16, 1978 - current boat
--