Hey Everyone,
I have been restoring a Mystere 6.0 (https://www.thebeachcats.com/forums/viewtopic/topic/18672)
I have have the hull lids, I have sanded down all contact areas and before I reglued these lids down I wanted to make sure I haven't missed anything.
1) Check rigging hardware isn't rusted and is securely attached to the hull
2) Ensure there are no cracks or holes on the inside of the hull
3) Reenforce where the bulkheads attached to the hull
4) Inspect centerboard housing and check for holes, cracks, etc.. Reenforce/patch where needed
5) Check for thin spots on the bottom of the hull where it may have been dragged or damaged
Have I missed anything? The last thing I want is to seal up the hulls and block myself from check or fixing something else
Before I seal my hulls for good . . . *A Checklist*
-
- Rank: Lubber
- Registered: Sep 26, 2021
- Last visit: Jun 08, 2023
- Posts: 70
Posted: Feb 21, 2022 - 10:43 AM
-
- Rank: Mate
- Registered: Jun 15, 2016
- Last visit: Apr 14, 2022
- Posts: 181
Posted: Feb 21, 2022 - 11:41 AM
Maybe epoxy clear coat a $10 bill to the hull for the next guy who goes is there?
Edited by traphappy on Feb 21, 2022 - 12:42 PM. -
- Rank: Mate
- Registered: Aug 18, 2003
- Last visit: Dec 13, 2023
- Posts: 880
Posted: Feb 21, 2022 - 02:29 PM
Does it have a track for the tramp? Check those rivets? -
- Rank: Mate
- Registered: Nov 22, 2012
- Last visit: Dec 05, 2024
- Posts: 415
Posted: Feb 21, 2022 - 04:53 PM
When you refer to rigging hardware, are you referring to side stay chain plates? I am not familiar with how the Mystere chain plates are installed, but I would try to look on the inside where the chain plate enters the deck. If water had seeped from the top and sat in between the stainless chain plate and the fiberglass, it could rust and deteriorate this point. With bigger boats, this is very common failure point.
--
Scott
Prindle Fleet 2
TCDYC
Prindle 18-2 Mod "FrankenKitty"
Tornado Classic "Fast Furniture"
Prindle 19 "Mr. Wiggly"
Nacra 5.8 "De ja vu"
Nacra 5.0
Nacra 5.8
Tornadoes (Reg White)
-- -
- Rank: Lubber
- Registered: Sep 26, 2021
- Last visit: Jun 08, 2023
- Posts: 70
Posted: Feb 21, 2022 - 05:26 PM
@texastuma - yes, chain plate stay thank you. I couldn't remember what they were called. I looked those over pretty well and there isn't any visible rust on anywhere. I am going to add some extra sealant for good measure but those look solid. -
- Rank: Lubber
- Registered: Jul 14, 2015
- Last visit: Dec 14, 2024
- Posts: 78
Posted: Feb 21, 2022 - 09:54 PM
Stainless can fail without showing rust. Look at the holes the pins go through, if they're elongated replace them.
Look for cracks or any deformity. Just replace them anyway, they're cheap.
The Bore
--
Dart 20
-- -
- Rank: Lubber
- Registered: Sep 26, 2021
- Last visit: Jun 08, 2023
- Posts: 70
Posted: Feb 22, 2022 - 01:46 PM
I appreciate all the advice. I checked everything mentioned and then some and have glued the panel down as of this afternoon. Fingers crossed I hope I did everything right -
- Rank: Mate
- Registered: Nov 22, 2012
- Last visit: Dec 05, 2024
- Posts: 415
Posted: Feb 22, 2022 - 05:29 PM
Excellent.. I've gone through that on a Prindle 19 twice.. different hulls. Now to get on the water..
--
Scott
Prindle Fleet 2
TCDYC
Prindle 18-2 Mod "FrankenKitty"
Tornado Classic "Fast Furniture"
Prindle 19 "Mr. Wiggly"
Nacra 5.8 "De ja vu"
Nacra 5.0
Nacra 5.8
Tornadoes (Reg White)
-- -
- Rank: Master Chief
- Registered: Jun 20, 2006
- Last visit: Dec 04, 2024
- Posts: 7090
Posted: Feb 23, 2022 - 08:22 AM
i agree if you inspect (use a magnifying glass) and find cracks, it is time to replace but
this is pretty serious surgury, even after the boat is opened up
the bow tangs are glassed in and would need to be hammered out to replace
the sidestay tangs have 3 bolts that are probably fused by now and also glassed in -
