This is the time of year we should going over our boats with a fine tooth comb looking for things that could possibly fail and ruin our day. But for some, the condition of the trailer is often overlooked and certainly carries the potential to ruin things as well. Springs, axles and U-bolts are obvious, wheel bearings aren't and the amount and type of usage should dictate how often you need to re-pack them. Their condition when you do re-pack them should give you an idea of how often this is needed. Don't rely on "Buddy Bearings" or their knockoffs. They may increase the interval but aren't a substitute for proper maintenance. One thing that does help however, is if your launching situation is where you don't have to submerge the hubs when launching. If you're uncertain about any of this, just get out and touch the hubs after going 50 mph. If they're hot, you'll know what to do. Another thing that might get overlooked is lug bolts. Don't get stuck because you're unable to change the wheel. Loosen the lug nuts every season and grease the bolts. Here's one thing that I overlooked, and that is where the yoke is bolted to the trailer tongue. On mine, the yoke is welded to a plate which is bolted to the trailer tongue. I saw a little rusty water gathering around that area. One might assume there should be a drain hole under there. I took the yoke off and turned it upside down and at least a pint of rusty water poured out of it. After it dried, I banged on it with a hammer and large chunks of rust fell out. There was a drain hole all right, but it was completely plugged.
--
Bill Townsend
G-Cat 5.0
Sarasota
--
Trailer maintenance
-
- Rank: Mate
- Registered: Apr 07, 2017
- Last visit: Nov 21, 2024
- Posts: 367
Posted: Jan 06, 2024 - 12:20 PM
-
- Rank: Mate
- Registered: Sep 23, 2022
- Last visit: Nov 15, 2024
- Posts: 104
Posted: Jan 06, 2024 - 10:59 PM
Well said. It doesn't matter how great your boat is if it's sitting on the side of the road. -
- Rank: Mate
- Registered: Sep 01, 2002
- Last visit: Oct 31, 2024
- Posts: 796
Posted: Jan 08, 2024 - 08:21 PM
Along with that, if taking long trips...get an extra hub or two complete with bearings already greased and ready to go.
https://www.amazon.com/dp/B01HP649RQ/ref=syn_sd_onsite_desktop_0?ie=UTF8&psc=1&pd_rd_plhdr=t&aref=71IOOvoMSO
Yes, you just cleaned a repacked them... but as robust as they are, they do take a beating.. at 55 MPH...
And, maybe one of these too..
https://www.harborfreight.com/12v-magnetic-led-towing-light-kit-64282.html
As for your lug nuts, apply generous amounts of Teflon plumbers paste or Loctite Marine Anti-Siez to the threads.... You don't want to be wrestling with those lugs in 100-degree weather or stripping them - trust me on this
Edited by JohnES on Jan 08, 2024 - 06:34 PM.
--
John Schwartz
Ventura, CA
-- -
- Rank: Mate
- Registered: Sep 01, 2002
- Last visit: Oct 31, 2024
- Posts: 796
Posted: Jan 08, 2024 - 08:36 PM
One other thing, check the tension spring for your connector.... these have been known to fail too
Edited by JohnES on Jan 08, 2024 - 06:37 PM.
--
John Schwartz
Ventura, CA
-- -
- Rank: Mate
- Registered: Jul 29, 2015
- Last visit: Jul 26, 2024
- Posts: 590
Posted: Jan 08, 2024 - 11:27 PM
Many years ago I spun the bearings on my catamaran trailer requiring a new axle, bearings and hub. That really sucked as I lost the weekend on the boat and had a big repair bill away from home. I routinely maintain the bearings now, but wish I didn't end up needing new bearing seals every time I disassemble the hubs. And it's always the inner bearing you can't see without pulling the hub.
--
Tom
NACRA 5.7 (1984 Sail 181)
Pennsylvania
-- -
- Rank: Mate
- Registered: Apr 07, 2017
- Last visit: Nov 21, 2024
- Posts: 367
Posted: Jan 09, 2024 - 10:44 AM
I have owned a total of 8 beachcats in my life, 4 of which the trailer's condition was questionable. Of those 4, I negotiated to have the boats brought to me before money exchanged hands. Those little wheels just turn too fast to trust the seller when they tell tell you they'll be okay.
A grease gun and buddy bearings won't get sufficient grease to the inner bearings.
--
Bill Townsend
G-Cat 5.0
Sarasota
-- -
- Rank: Lubber
- Registered: Jul 11, 2014
- Last visit: Mar 18, 2024
- Posts: 80
Posted: Mar 18, 2024 - 10:57 PM
Forgot to sign in...
"A grease gun and buddy bearings won't get sufficient grease to the inner bearings." I do not use the "Bearing Buddies" to lube the bearings. By the time you put enough pressure in there to actually push grease through the bearings, you would probably push the "buddy" cap out. Instead, I use them to, right before launch, pump a couple squirts into them,[enough to see the spring plate move a bit]. This in my opinion, pressurizes the hub so that they do not accept water. The hubs should not get more than, "kinda warm I guess", if bearings are greased well.
--
1978 H18
1983 H18 (some of it)
--
