|
Blade F16 Building Slideshow
Date: 03/11/2006
Views: 7787
|
Plane the edges of ply to a 10:1 taper
Date: 03/11/2006
Views: 4645
|
pic003-fine sand with a block and sandpaper or fine grade worn belt on belt sander
Date: 03/11/2006
Views: 4216
|
pic004-pic shows the tapered sheets of ply before the scarf is joined with epoxy resin glue mix
Date: 03/11/2006
Views: 4079
|
|
pic005-apply the glue evenly to all sheets at once
Date: 03/11/2006
Views: 4033
|
pic006-carfully stack the sheets and then clamp so they glue to make 16ftx4ft sheets
Date: 03/11/2006
Views: 3790
|
pic007-cut out hull sides and glue on gunwales and stringers
Date: 03/11/2006
Views: 4001
|
pic008-Reinforcing the bow tip to take the loading from the spinnaker pole lines.
Date: 03/11/2006
Views: 3865
|
|
pic009-Stitch together the hull sides and keel panel with wire copper wire.
Date: 03/11/2006
Views: 4500
|
pic010-Spread the gunwales to flatten the keel area before filletting and glassing the keel joins.
Date: 03/11/2006
Views: 4091
|
pic011-Check to make sure they are as described in the plans before glassing.
Date: 03/11/2006
Views: 3653
|
pic012-Fillet and glass the inside of the keel.
Date: 03/11/2006
Views: 3736
|
|
pic013-Applying glass tapes to the keel inside.
Date: 03/11/2006
Views: 3687
|
pic014-Tapes are fitted to pre-drawn limits.
Date: 03/11/2006
Views: 3794
|
pic015-Slightly round the outside on the keel join.
Date: 03/11/2006
Views: 3596
|
pic016-Apply packing tape to avoid resin runs when glassing the outside join.
Date: 03/11/2006
Views: 3955
|
|
pic017-Prime with Resin.
Date: 03/11/2006
Views: 3507
|
pic018-Apply tapes to outside join.
Date: 03/11/2006
Views: 3457
|
pic019=Carefully wet tapes out with resin.
Date: 03/11/2006
Views: 3357
|
pic020-Fit hull into expanded deck jig.
Date: 03/11/2006
Views: 3663
|
|
pic021-Hull positioned ready for the steaming process to begin.
Date: 03/11/2006
Views: 3916
|
pic022-Cut thru the outside glass and ply but not inside glass for first 200mm(8") from the bow. This part will not be able
pic022-Cut thru the outside glass and ply but not inside glass for first 200mm(8") from the bow. This part will not be able to take the bend so better cut than crack the ply.
Date: 03/11/2006
Views: 3743
|
pic023-Steam the hull with towels and boiling water.
Date: 03/11/2006
Views: 3731
|
pic024-Slowly and carefully torture the ply into the hull shape.
Date: 03/11/2006
Views: 3812
|
|
pic025-The steaming is now complete.
Date: 03/11/2006
Views: 4028
|
pic026-Clamp the bow while the hull dries.
Date: 03/11/2006
Views: 3570
|
pic027-Ties around hull to move it from upside down adjustable to upright fixed deck jig for fitting out.
Date: 03/11/2006
Views: 3796
|
pic028-Hull sitting in deck jig.
Date: 03/11/2006
Views: 3637
|
|
pic029-Deck jig helps define the shape of the hull and width of the deck.
Date: 03/11/2006
Views: 3821
|
pic030-Front view of hull in deck jig.
Date: 03/11/2006
Views: 3581
|
pic031-Showing bow and keel shape from the front.
Date: 03/11/2006
Views: 3764
|
pic032-Showing how all 4mm bulkheads and decks can come out of 1 sheet of ply.
Date: 03/11/2006
Views: 3665
|
|
pic033-Cutting B/H out with jig saw.
Date: 03/11/2006
Views: 3130
|
pic034-Trimming B/H with template and router.
Date: 03/11/2006
Views: 3305
|
pic035-Just showing the profile of the modern Blade F16 shape.
Date: 03/11/2006
Views: 3536
|
pic036-Fitting the centrecase
Date: 03/11/2006
Views: 3422
|
|
pic037-Make sure the centre case in perp to the keel and then fix it in place.
Date: 03/11/2006
Views: 3617
|
pic038-Centrecase, rear beam b/h and landing ,transom and c/s b/hs fitted.
Date: 03/11/2006
Views: 3411
|
pic039-View of transom fitted and hull waterproofed with resin.
Date: 03/11/2006
Views: 3275
|
pic040-View of rear beam b/h
Date: 03/11/2006
Views: 3429
|