|
IMG_0050
And after you slather on the marine tex with an old dirty mop...
Date: 05/03/2009
Views: 1230
|
IMG_0051
looks like several bad bottom jobs in the past
Date: 05/03/2009
Views: 1111
|
IMG_0059
A really rotten tramp, I could poke my finger through it in several places
Date: 05/03/2009
Views: 1065
|
IMG_0060
the neighbors are so not loving me...promised rides for everyone wenty a long way to smoothing things over
Date: 05/03/2009
Views: 1111
|
|
IMG_0066
After removing all the marine tex the real damage was revealed
Date: 05/03/2009
Views: 1165
|
IMG_0067
more epoxy and glass and still a long way to go
Date: 05/03/2009
Views: 1136
|
IMG_0071
broken screw in drain plug, still not sure what to do about this yet but got new metal drain plug bracket to go back on
Date: 05/04/2009
Views: 1061
|
IMG_0073
some new epoxyand a sheet of glass tape but a long way to go till done
Date: 05/04/2009
Views: 1066
|
|
IMG_0080
salt ate the nylon screws so i had to drill them out and chase the threads with a bolt. the 99 cent pcoket torcvh was a great help thanks harbor freight
Date: 05/18/2009
Views: 1189
|
IMG_0082
the castings had a lot of burrs on them so I used a fine flat file to clean them up
Date: 05/18/2009
Views: 1116
|
IMG_0083
making good progress, the brown is filler and west systems may be god awful expensive but it is worth every penny!
Date: 05/18/2009
Views: 1109
|
IMG_0084
you have to use your hands to feel the shape as your eyes will play tricks on you. This hull is all but ready for paint
Date: 05/18/2009
Views: 1240
|
|
IMG_0085
what it takes to epoxy and paint out side during love bug season, the neighbors love me...
Date: 05/18/2009
Views: 1135
|
IMG_0086
Same for the cam adjuster screw, drilled out and cleaned with pocket torch and bolt
Date: 05/18/2009
Views: 1066
|
IMG_0088
sails look pretty good but the rust spots are there to stay even after a serious round with remover
Date: 05/24/2009
Views: 1003
|
IMG_0089
redid the battons to include new ends at luff and leacch and new lines. wish i knew the name of this color
Date: 05/24/2009
Views: 1357
|
|
IMG_0124
rudders before and after glass and paint, half way there!
Date: 06/10/2009
Views: 1082
|
IMG_0130
1 hull down and 1 to go. Wiosh I could paint as weel as I can glass. shape was good but bad paint job with lots of runs set me back a bit. Better now
Date: 06/10/2009
Views: 1043
|
IMG_0132
2nd hull done. I am no painter but I think i did pretty good considering I had a bad spray gun
Date: 06/16/2009
Views: 1214
|
IMG_0133
If you do get runs, WET SANDING IS THE ONLY WAY TO GO. it is much easier and get better results with a lot less effort. Wish I knew this from the start!
Date: 06/16/2009
Views: 1022
|
|
ready to put the hardware back on, chased the threads and dry fitted before I put any sealant on. It helps to have a lower casting with no rudder so you can be sure everything lines up
Date: 06/16/2009
Views: 1035
|
IMG_0140
make sure everything lines up and is threaded correctly before you press in the sealant. having to pull it apart and redo it can lead to bubbles and early failure
Date: 06/16/2009
Views: 1011
|
the pin moves freely! Note the cool new all metal plug housings
Date: 06/16/2009
Views: 1013
|
IMG_0142
sealing the joint, the one time it is a good thing to give your boat the finger!
Date: 06/16/2009
Views: 1095
|
|
IMG_0143
make sure to force the sealant into all the little cracks and holes. This will go a long way to keeping water out when you are really working the boat hard
Date: 06/16/2009
Views: 1032
|
IMG_0144
rebuilt castings with rudder stiffening kit. Slip the disks in then use an awl to ge them all lined up. Tighten nuts till movement stiffens then back off till free again
Date: 06/17/2009
Views: 1017
|
IMG_0145
Remember to keep the nuts on the insides. I scratched P and S into the castings before I took them apart just to be sure they went on the same way they came off for new parts, this does not matter much but for 22 year old parts IT DOES!
Date: 06/17/2009
Views: 997
|
IMG_0146
by some miracle, I was able to put her back together by my self. The foam blocks were perfect for proping things in place
Date: 06/19/2009
Views: 1004
|
|
IMG_0147
I forgot to take pics while lacing up the tramp but I was a little busy any way. A marlin spike wedged into a gromet is a great way to hold the tension until you can relocate. This tramp only cost $150 off ebay and fit great. I also added tramp clamps in
Date: 06/20/2009
Views: 1082
|
IMG_0148
not sure I laced it right but I do know I laced it tight and figured out a way to hide all the knots underneath.
Date: 06/20/2009
Views: 1048
|
IMG_0161
she looks ready for the water so Wednesday is a go!!!
Date: 06/21/2009
Views: 1087
|
IMG_0163
Harken 6:1 75mm carbo block. Had to "make" it fit the traveler but otherwise, works great and the mainsheet is huge
Date: 06/21/2009
Views: 1081
|
|
IMG_0165
Ready for her maiden voyage!!!
Date: 06/28/2009
Views: 1196
|
IMG_0168
An incredible day with perfect conditions. only bummer was breaking both main and jib cleats on mast. No biggie, will oredr new ones and be good to go but they are still useable as is.
Thanks for all the help and to every one else, what a...
Date: 06/28/2009
Views: 1210
|
|
|
